background image

2. 

Operation & Specifications

2 - 19

SPECIFICATIONS

MB26J

PARAMETER

MB26J EU VERSION

MB26J US VERSION

Duty Cycle

45%over 8 hour cycle

35%over 8 hour cycle

Platform Size

770mm x 730mm

30.5in. x 28.5in.

Maximum Platform Capacity

215kg.

475lbs.

Indoors

2 People

2 People

Outdoors

1 Person

2 People

Max Wind Speed

12.5 m/s

26.8 mph

Max Manual Force Per Person

200N

45lbs

Maximum Chassis Inclination

Heights:

Maximum Platform Height

7.75m

25.45ft.

Maximum Working Height

9.75m

32.00ft.

Platform Height at Maximum Outreach

6.51m

21.36ft.

Maximum Working Outreach

3m

10ft.

Stowed Dimensions:

Length

2.800m

9.2ft.

Width

1.010m

40in.

Height

2.010m

6.59ft.

Chassis Ground Clearance

90mm

3.54in.

Wheelbase x Wheel Gauge

1465mm x 890mm

4.81ft. x 2.93ft.

Rotation

360deg non-continuous

360 deg non-continuous

Gross Vehicle Weight

2660kg.

7000lbs.

Maximum Drive Speed - Stowed

3.13 km/h

1.94mph.

Maximum Drive Speed - Elevated

0.60km/h

0.37mph

Maximum Gradeability

25%

25%

Outside Turning Radius

1.93m

6.33ft.

Electrical:

Power Source

4 x 6V @ 375Ah Battery

4 x 6V @ 375Ah Battery

System Voltage

24 Volt DC

24 Volt DC

Battery Charger ( 2 Per Machine )

24V x 30A, Output

24V x 30A, Output

Auto Select AC input

Auto Select AC input

100-240v -50/60Hz 12-6A

100-240v -50/60Hz 12-6A

Control System

Single Joystick, Function 

Selector, DC Motor Controller

Single Joystick, Function 

Selector, DC Motor Controller

Hydraulic System:
System Relief Setting

220bar

3190psi

Hydraulic Oil Type

ISO VG46 

ISO VG46

Hydraulic Tank Capacity

18 litres

4.7 gallons (U.S.)

Brakes

Spring applied hydraulically

 

released

Spring applied hydraulically 

released

Wheels & Tyres

13.5in x 4.0

solid, Non-Marking

13.5in x 4.0

solid, Non-Marking

Wheel loading

1300kg per wheel

3566lbs per wheel

Vibration of this machine does not exceed

2.5m/sec

 х2

2.5m/sec

 х2

Noise Pressure Level

68dB (A) at Control Station

68dB (A) at Control Station

Содержание MB20J

































Отзывы: