background image

GB - 30

Engine stops.

1. Out of fuel.

2. Fuel shut-off valve 

closed.

3. Mechanical jam in auger 

or impeller.

4. Contaminated fuel supply.
5. Faulty spark plug.
6. Plugged fuel cap vent.

1. Fill fuel tank. DO NOT 

OVERFILL! (see 

Filling Fuel 

Tank

 on page 15)

.

2. Open fuel shut-off valve.

3. Turn off engine, remove key, 

and wait for all moving parts to 
stop. Check for and remove 
obstruction and repair before 
restart.

4. Replace with clean fuel.
5. Replace or clean spark plug.
6. Replace fuel cap.

Engine 
problems.

1. See Engine Manual.

1. See Engine Manual.

Does not 
operate in 
Forward / 
Reverse.

1. Friction disc worn out.

2. Traction belt not 

functioning.

3. Speed selector not 

adjusted properly.

1. Replace friction disc 

(see 

Replace Attachment Drive Belt 

on page 25).

2. Repair or replace traction drive 

belt 

(see Traction Drive Belt 

Replacement 

on page 26).

3. Adjust speed selector

 (see 

Speed Selector Adjustment 

on 

page 22).

Small rubber 
beads collect 
in frame

1. Friction disc wear.

1. Normal friction disc wear. 

Chunks or large pieces of 
rubber mean friction disc 
should be checked and 
replaced as necessary.

Unit throws 
snow poorly 
or does not 
throw snow.

1. Shear bolts broken.

2. Attachment clutch/brake 

not adjusted properly.

3. Auger is frozen in place.

4. Ice or debris is 

obstructing auger.

5. Attachment drive belt 

slipping, worn or 
damaged.

1. Replace shear bolts 

(see Shear 

Bolts 

on page 21).

2. Adjust attachment clutch/brake 

(see Attachment Clutch/Brake 
Adjustment 

on page 23).

3. Move unit to a warm place to 

thaw.

4. With the engine off and auger 

disengaged, check for 
obstructions and remove.

5. Adjust or replace attachment 

drive belt 

(see Attachment 

Clutch/Brake Adjustment 

on 

page 23).

TROUBLESHOOTING

PROBLEM

PROBABLE CAUSE

CORRECTION 

Содержание 920402-Sno-Tek 24E







































Отзывы: