Snapper Pro 5901280 Скачать руководство пользователя страница 50

Страница: 50 / 56

Not for

Reproduction

Problem: Stepped Cutting

Stepped cutting is sharp ridges or uneven levels left in the lawn surface.
Stepped cutting is usually caused by mower deck damage or misadjustment,
or damage to the mower blades.

Remedy

Cause

Level the deck correctly.

Deck is not leveled correctly.

Check and inflate the tires.

Tires are not properly inflated.

Replace the blades.

Blades are damaged.

Repair or replace the deck.

Deck shell is damaged.

Repair or replace the spindle.

Mower spindle is bent or loose.

Reinstall the blades correctly.

Blades are installed incorrectly.

Problem: Uneven Cutting

Uneven cutting is waviness or smooth troughs in the lawn surface. Uneven
cutting is usually caused by mower deck damage or misadjustment.

Remedy

Cause

Level the deck correctly.

Deck is not leveled correctly.

Sharpen or replace the blades.

Blades are dull or worn.

Replace the blades.

Blades are damaged.

Clean out the deck.

Deck is clogged with grass clippings.

Repair or replace the deck.

Deck shell is damaged.

Repair or replace the spindle.

Mower spindle is bent or loose.

Reinstall the blades correctly.

Blades are installed incorrectly.

Check and inflate the tires.

Tires are not properly inflated.

Problem: Stringers

Stringers are sparse patches of uncut grass left behind the mower. Stringers
are usually caused by operator error or poor blade maintenance.

Remedy

Cause

Sharpen your blades.

Blades are not sharp or nicked.

Replace your blades.

Blades are worn down too far.

Always mow at full throttle.

Engine speed is too slow.

Slow down.

Ground speed is too fast.

Clean out the mower.

Deck is plugged with grass.

Specifications

Specifications are correct at time of printing and are subject to
change without notice.

ENGINE

For complete engine specifications see the engine
manufacturer's operator's manual included with your unit.

Fits models: 5901280

Briggs & Stratton Commercial Turf 49T877

Briggs & Stratton

Make

49T877-0010-G1

Model

12 volt, 16 amp alternator; Battery: 340
cca

Electrical System

Fits models: 5901663

Briggs & Stratton Vanguard 49R977

Briggs & Stratton

Make

49R977-0001-G1

Model

12 volt, 16 amp alternator, Battery: 340
cca

Electrical System

Fits models: 5901664

Kawasaki FX801V

Kawasaki

Make

FX801V

Model

12 volt, 15 amp charging coil; Battery:
340 cca

Electrical System

Fits models: 5901665

Briggs & Stratton Vanguard EFI

Briggs & Stratton

Make

49E877-0009-G1

Model

12 volt, 20 amp alternator, Battery: 340
cca

Electrical System

Fits models: 5901666 & 5901667

Briggs & Stratton Vanguard EFI

Briggs & Stratton

Make

61E877-0005-J1

Model

12 volt, 20 amp alternator, Battery: 340
cca

Electrical System

Fits models: 5901708

Briggs & Stratton Vanguard EFI

Briggs & Stratton

Make

543777-2125-J1

Model

snapperpro.com

Содержание 5901280

























































Результаты поиска

Содержание 5901280

Отзывы:

Бренды по названию

Популярные бренды

Snapper Pro 5901280, Руководство оператора

Результаты поиска

Содержание 5901280

Отзывы:

Бренды по названию

Популярные бренды