Snap-On EEWB304B Скачать руководство пользователя | Manualshive

Страница: 6 / 28

background image

Page 4

1.0 INTRODUCTION

Congratulations on purchasing the

EEWB304B

computer wheel balancer. This wheel balancer is de-

signed for ease of operation, accuracy, reliability and speed. With a minimum of maintenance and care
your wheel balancer will provide many years of trouble-free operation.

Instructions on use, maintenance and operational requirements of the machine are covered in this
manual.

STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.
READ THIS MANUAL THOROUGHLY BEFORE USING THE MACHINE.

1.1 SAFETY NOTICE

This manual is a part of the balancer product.

Read carefully all warnings and instructions of this manual since they provide important information
concerning safety and maintenance.

1.2 BALANCER APPLICATION

The Snap-on wheel balancer model EEWB304B is intended to be used as a device to balance car, and
light truck wheels within the following range:

Maximum wheel diameter

:

44” (1117mm)

Maximum wheel width

:

16” (530mm)

Maximum wheel weight

:

130lbs (58.5 kg)

This device is to be only used in the application for which it is specifically designed.
Any other use shall be considered as improper and thus not reasonable.

The manufacturer shall not be considered liable for possible damages caused by improper, wrong or
non reasonable use.

«
...
4
5
6
7
8
...
»

Содержание EEWB304B





























Отзывы:

Нет отзывов

Похожие инструкции для EEWB304B

Бренд: Hofmann Страницы: 128

VIDEOTRONIC V548.G4

Бренд: Fasep Страницы: 19

Бренд: BRIGHT Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды