manualshive.com logo in svg

SMSC LAN9312, Техническое описание


Поделиться
Скачать
background image

High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface

Datasheet

Revision 1.4 (08-19-08)

138

SMSC LAN9312

DATASHEET

 

10.2.1

EEPROM Controller Operation

I

2

C and Microwire master EEPROM operations are performed using the 

EEPROM Command Register

(E2P_CMD)

 and 

EEPROM Data Register (E2P_DATA)

. 

In Microwire EEPROM mode, the following operations are supported:

„

ERASE (Erase Location)

„

ERAL (Erase All)

„

EWDS (Erase/Write Disable)

„

EWEN (Erase/Write Enable)

„

READ (Read Location)

„

WRITE (Write Location)

„

WRAL (Write All)

„

RELOAD (EEPROM Loader Reload - See 

Section 10.2.4, "EEPROM Loader"

)

Note:

In I

2

C EEPROM mode, only a sub-set of the above commands (READ, WRITE, and RELOAD)

are supported.

Note:

The EEPROM Loader uses the READ command only.

The supported commands of each mode are detailed in 

Section 14.2.4.1, "EEPROM Command

Register (E2P_CMD)," on page 197

. Details specific to each EEPROM controller mode (I

2

C and

Microwire) are explained in 

Section 10.2.2, "I2C EEPROM"

 and 

Section 10.2.3, "Microwire EEPROM"

respectively.

When issuing a WRITE, or WRAL command, the desired data must first be written into the 

EEPROM

Data Register (E2P_DATA)

. The WRITE or WRAL command may then be issued by setting the

EPC_COMMAND field of the 

EEPROM Command Register (E2P_CMD)

 to the desired command

value. If the operation is a WRITE, the EPC_ADDRESS field in the 

EEPROM Command Register

(E2P_CMD)

 must also be set to the desired location. The command is executed when the EPC_BUSY

bit of the 

EEPROM Command Register (E2P_CMD)

 is set. The completion of the operation is indicated

when the EPC_BUSY bit is cleared.

When issuing a READ command, the EPC_COMMAND and EPC_ADDRESS fields of the 

EEPROM

Command Register (E2P_CMD)

 must be configured with the desired command value and the read

address, respectively. The READ command is executed by setting the EPC_BUSY bit of the 

EEPROM

Command Register (E2P_CMD)

. The completion of the operation is indicated when the EPC_BUSY

bit is cleared, at which time the data from the EEPROM may be read from the 

EEPROM Data Register

(E2P_DATA)

.

Other EEPROM operations (EWDS, EWEN, ERASE, ERAL, RELOAD) are performed by writing the
appropriate command into the EPC_COMMAND field of the 

EEPROM Command Register

(E2P_CMD)

. The command is executed by setting the EPC_BUSY bit of the 

EEPROM Command

Register (E2P_CMD)

. In all cases, the software must wait for the EPC_BUSY bit to clear before

modifying the 

EEPROM Command Register (E2P_CMD)

.

Note:

The EEPROM device powers-up in the erase/write disabled state. To modify the contents of
the EEPROM, the EWEN command must first be issued.

If an operation is attempted and the EEPROM device does not respond within 30mS, the LAN9312
will time-out, and the EPC_TIMEOUT bit of the 

EEPROM Command Register (E2P_CMD)

 will be set.

Содержание LAN9312











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LAN9312

Xunison Hub M50 Mesh Cube Quick Start Manual preview
Hub M50 Mesh Cube
Бренд: Xunison Страницы: 11
ADDER GEMAV2GEM Installation And Use Manual preview
GEMAV2GEM
Бренд: ADDER Страницы: 46
WoMaster DS105 Quick Installation Manual preview
DS105
Бренд: WoMaster Страницы: 2
ANTAIRA LMP-1204G-SFP Series Hardware Manual preview
LMP-1204G-SFP Series
Бренд: ANTAIRA Страницы: 20
CYP CDPS-UA6H2HFS Operation Manual preview
CDPS-UA6H2HFS
Бренд: CYP Страницы: 32
Crestron CLW-LSWEX-1GD Installation And Operation Manual preview
CLW-LSWEX-1GD
Бренд: Crestron Страницы: 2
Eaton TM-1-8210 Series Instruction Leaflet preview
TM-1-8210 Series
Бренд: Eaton Страницы: 3
Velleman HQ-Power VMS4 Manual preview
HQ-Power VMS4
Бренд: Velleman Страницы: 5
Eaton STS 2000A Installation And Operation Manual preview
STS 2000A
Бренд: Eaton Страницы: 120
Moxa Technologies PT-G7509 Hardware Installation Manual preview
PT-G7509
Бренд: Moxa Technologies Страницы: 7
TRENDnet TE100-S24D Specifications preview
TE100-S24D
Бренд: TRENDnet Страницы: 2
NBK EORP-200 Instruction Manual preview
EORP-200
Бренд: NBK Страницы: 32
SICK MSL Series Operating Instructions Manual preview
MSL Series
Бренд: SICK Страницы: 299
ATEN AS-251S User Manual preview
AS-251S
Бренд: ATEN Страницы: 4
Edge-Core ECS2000-18P Installation Manual preview
ECS2000-18P
Бренд: Edge-Core Страницы: 65
J-TECH JTECH-4K88-EX-RX Operating Instructions Manual preview
JTECH-4K88-EX-RX
Бренд: J-TECH Страницы: 40
Enterasys SecureStack B2 B2G124-48P Hardware Installation Manual preview
SecureStack B2 B2G124-48P
Бренд: Enterasys Страницы: 91
H3C IE4300-12P-PWR Installation Manual preview
IE4300-12P-PWR
Бренд: H3C Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды