Smiths Medical Oxi-Pulse 30 Скачать руководство пользователя страница 60

Страница: 60 / 66

Chapter 9: Troubleshooting

9-4

Home Use Operation Manual

PRObleM

POSSIble CAUSe

CORReCTIVe ACTIOn

SpO

value is erratic,

intermittent, or

incorrect.

Poor patient perfusion.

Patient motion.

Defective sensor or patient

cable.

Confirm signal level with PI and signal

bar graphs.

Reposition the sensor on the patient.

Patient must remain still to obtain an

accurate measurement.

Try a new sensor or contact your

authorized service representative for

help.

Oximeter Alert.

Oximeter cable or sensor

is disconnected from the

oximeter.

Sensor is incorrectly

positioned on the patient.

Poor patient perfusion.

Oximeter searching too long

for initial SpO

signal.

Check sensor connections to the patient

cable and to the oximeter.

Reposition the sensor.

Confirm signal level with PI and signal

bar graphs. Reposition the sensor on the

patient.

Confirm signal level with PI and signal

bar graphs. Check sensor connections

to the patient cable and to the oximeter.

Reposition the sensor on the patient.

Printer and Data Communication

PRObleM

POSSIble CAUSe

CORReCTIVe ACTIOn

No printout on

optional printer.

AC power is not connected to

the Docking Station.

No trends in memory.

No paper or paper incorrectly

loaded.

Connect AC Power to the Docking

Station.

Take trend data.

See

Chapter 7: Optional Docking Station

and Printer

for details of loading paper.

“?” malfunction

indicator on the

printer is lit.

Printer interface malfunction.

Printer door open.

Printer out of paper.

Contact your authorized service

representative for help.

Close the printer door.

Install a roll of printer paper.

Real time or

trend data is not

transmitted.

An accessory cable is

defective.

Oximeter is not properly

seated in Docking Station.

The communications setup is

not correct.

Contact your authorized service

representative.

Remove the oximeter from the Docking

Station and replace it assuring proper

alignment.

Check the user-connected auxiliary

equipment and software.

Содержание Oxi-Pulse 30


































































Результаты поиска

Содержание Oxi-Pulse 30

Отзывы:

Похожие инструкции для Oxi-Pulse 30

Бренды по названию

Популярные бренды

Smiths Medical Oxi-Pulse 30, Руководство по эксплуатации для домашнего использования

Результаты поиска

Содержание Oxi-Pulse 30

Отзывы:

Похожие инструкции для Oxi-Pulse 30

Бренды по названию

Популярные бренды