SMC Networks ZK2 A Series Скачать руководство пользователя

Страница: 76 / 80

-75-

No. ZK2-OM01301

In addition, the exhaust port should not be blocked or pressurized.

If the sound absorbing material is clogged, it will cause a reduction in the ejector performance.

Sometimes, if the operating environment contains a lot of particles or mist, the replacement of the filter

element only is not enough to recover vacuum performance

– as the sound absorbing material may be

clogged. Replace the sound absorbing material. (Regular replacement of the filter element and sound

absorbing material is recommended.)

■

Exhaust Noise

When vacuum ejector generates vacuum, noise can be heard from the exhaust port when the standard

supply pressure is close to the pressure that generates peak vacuum pressure making vacuum pressure

unstable. If the vacuum pressure range is adequate for adsorption, there should not be a problem. If the noise

causes a problem or affects the setting of the pressure switch, change the supply pressure slightly to avoid

the pressure range of the noise.

■

Maximum Number of Manifold Stations that Can Operate Simultaneously

Note)

Note) As long as the number of stations operated simultaneously is the value on the table or less, then the manifold is

available up to 10 stations.

Item

ZK2

□07 ZK2□10 ZK2□12 ZK2□15

Air pressure

supply (PV)

port

ø8, ø5/16

”

Complex exhaust

Supply from one side

Supply from both sides

Individual port exhaust,

High-noise reduction

silencer exhaust

Supply from one side

Supply from both sides

Peak vacuum
pressure

uum

res

sure

Standard supply pressure

Pressure range of the noise

Supply pressure

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды