SMC Networks ZK2 A Series страница 17 Скачать руководство пользователя

Страница: 17 / 80

-16-

No. ZK2-OM01301

3. Installation

3.1. Installation

■

Single Unit

1. DIN rail mounting

1) Insert a precision screwdriver into the groove of the release lever and push in direction (1), and slide the

filter case in direction (2).

2) Hook the ejector onto the DIN rail from direction (3) and mount the ejector onto the DIN rail by pushing it

down in direction (4).

3) Push the filter case assembly in direction (5) until it is locked.

4) To hold the ejector onto the DIN rail, hold it from both sides using the stopper brackets.

2. Direct mounting

1) Mount and tighten the body using the holes in the body (2 x ø4.5).

(Tightening torque : 0.75 N

・

(3)

(4) (5)

2 x ø4.5 Mounting hole

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды