SMC Networks LECSA Series Скачать руководство пользователя страница 87

Страница: 87 / 96

7.4 Positioning Mode (Point table method)

Positioning operation can be executed by setting the target position, rotation speed, acceleration time constant,
deceleration time constant to the point table data. (The maximum points that can be set in point table is 7.)

See

“

LEC

SA Operation Manual”,section 13.3 for details regarding the positioning mode (point table).

7.4.1 Operation Instruction of Point Table system

Select the point table No. represented by the values of DI0, DI1 and DI2. Start the operation by selecting ST1 or
ST2.

Device

Symbol

Connector

pin No.

Functions/Applications

I/O

division

Positioning

mode

Point table No.

/Program No.

selection 1

DI0

CN1-5

The point table No. and the home position return

mode are selected by DI0 to DI2.

The program No. is selected by DI0 to DI2.

DI-1

(Note)

Device

Selection description

Point table No.

/Program No.

selection 2

DI1

CN1-23

DI2 DI1 DI0

Point table method

DI-1

Home position return mode

Point table No. 1

Point table No. 2

Point table No. 3

Point table No. 4

Point table No.

/Program No.

selection 3

DI2

Point table No. 5

DI-1

Point table No. 6

Point table No. 7

Note. 0: off

1: on

Program

input 1

PI1

Turn PI1 on to resume the step stopped by the

SINK (1) command in the program.

DI-1

If the parameter " PE01

：

Command mode selection " setting is "0000

：

Absolute value command system " .

Point table No.

Target position

[×10

STM

μm]

Rotation speed

[r/min]

Acceleration

time constant

[ms]

Deceleration

time constant

[ms]

Dwell

[ms]

Auxiliary

function

5.00

3000

100

150

100

-6.00

2000

100

3.00

3000

0 (Note)

Note. Always set "0" or "2" to the auxiliary function in the last point table among the consecutive point tables.

0: When point table is used in absolute value command system

2: When point table is used in incremental value command system

Содержание LECSA Series

































































































Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды

SMC Networks LECSA Series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды