background image

 
 

Doc. no.IZ

-OMV0005 

 

24 

4-4. Alarm function 

If abnormal functioning occurs during operation, the user is alerted by the external output signal or LED operation.

 

Alarm name 

Status of the parallel I/O signals 

ON 

LED 

LED blinking 

(Blinks at 1Hz) 

Operation after alarm 

+ ions are generated 

Product 

How to release error 

after recovery 

Power supply 
failure 

Error signal OFF (Break contact) 

Discharge signal OFF(Albeit contact) 

Maintenance signal OFF (Albeit contact) 

PWR 

(Green) 

Stop 

When the connected power 
supply voltage is outside of 
the specification. 

Auto 

Incorrect 
high voltage 

Error signal OFF (Break contact) 

Discharge signal OFF(Albeit contact) 

Maintenance signal OFF (Albeit contact) 

ION/HV 

(Red) 

Stop 

When abnormal high voltage 
is discharged. 

Reset signal input   

Turn the power on 

again 

Output signal 
over current 

ION/HV 
(Green) 

Continue 

Over current is present on 
the output circuit    and 
protection circuit is activated 

Auto 

CPU ALM 

Error signal OFF (Break contact) 

Discharge signal OFF(Albeit contact) 

Maintenance signal OFF (Albeit contact) 

PWR (green) 

Stop 

When CPU operates 
abnormally due to noise etc. 

Turn the power on 

again. 

ION/HV (red) 

NDL (green) 

Maintenance 
warning 

Maintenance signal ON(Albeit contact) 

NDL 

(Green) 

Continue 

When static neutralization 
performance is reduced due 
to contamination, wearing or 
breakage of emitters. 

Input ion discharge 

signal 

Turn off the power and 

then on again. 

 

1) Power supply failure 

When the power supply connected to the product is not within the range of 24 V +/-10%, the error signal 

will  be  turned  OFF  (ON  when  it  is  normal),  the  discharge  signal  will  be  turned  OFF,  and  the  PWR  LED 
(green) will flash to indicate the error. 

When the failure occurs, ion generation will be stopped. 
To resolve the error, reset the product automatically by connecting a power supply which provides a power 

supply voltage of 24 V +/-10%. 

 

2) Incorrect high voltage 

When  incorrect  emitter  discharge  is  detected  during  operation,  the  error  signal  will  be  turned  OFF  (ON 

when it is normal), the discharge signal will be turned OFF, and the ION/HV LED (red) will be ON to indicate 
the error. 

When the failure occurs, ion generation will be stopped. 
The incorrect electric discharge could be caused by condensation or dust on the emitters. 
To resolve the error, input the reset signal or supply power again after remedying the cause of the incorrect 

electric discharge. 

 

3) Output signal over current 

When excessive current flows to the output circuit, the current will be limited to protect the circuit and the 

ION/HV LED (green) will flash to indicate the error. 

The product operates even when excessive current is generated in the output circuit. 
To resolve the error, reset the product automatically by reducing the current to the output circuit down to 40 

mA or less. 

 

4) CPU error 

When the CPU makes an abnormal operation due to noise or other reasons, the error signal will be turned 

OFF (ON when it is normal), and the PWR LED (green), ION-HV LED (red) and NDL LED (green) will flash to 
indicate the error. 

When the failure occurs, ion generation is stopped. 
To prevent noise, perform the following actions and take countermeasures. 

1. Keep the product away from sources of noise.   
2. Route the power line and cable of the product separately. 
3. Install a noise filter to the power supply of the product.   

To resolve the error, supply power again after fixing the cause of the error. 

 

5) Maintenance warning 

The  maintenance  signal  is  ON  when  static  electricity  neutralization  performance  has  decreased  due  to 

contamination, wear or damage to the emitters. The NDL LED (green) will turn ON to indicate that cleaning 
or replacement of the emitters needs to be performed. 

The product continues operation even when the maintenance warning has been generated. 
When emitters are contaminated, the error can be solved by cleaning them. However, when they are worn 

out or damaged, it is necessary to replace the emitter assembly.   

To resolve the error, input the discharge stop signal or supply power again after remedying the cause of 

the error. 

When  the  female  threads  for  piping  option  is  used,  the  maintenance  signal  will  turn  ON  if  the  nozzle 

pressure increases (causing the ion generation to decrease) due to the nozzle type.

 

 

Содержание IZN10E Series






































Отзывы: