SMC Networks EX600-DXPD 16 Series страница 21 Скачать руководство пользователя

Страница: 21 / 62

-20-

No.EX

※※

-OMU1021-A

LED Display

LED display shows the power supply and communication status.

Display

Content

ST(M)

Displays the diagnosis status of the unit.

PWR

Displays the status of the power supply voltage for control
and input.

PWR(V)

Displays the status of the power supply voltage for output.

Displays the module status.

Displays the network status.

Display

Content

L/A IN

Displays the communication status of the BUS IN side.

L/A OUT

Displays the communication status of the BUS OUT side.

•ST(M)-LED

LED display

Content

OFF

The power supply for control and input is OFF.

Green ON

Normal operation.

Green flashing

Diagnostic error of I/O unit is detected.

Red flashing

Either of the following diagnostic error is detected.
(When diagnostic parameter is enabled)
•Valve ON/OFF counter has exceeded the set value.
•Valve is short circuited or disconnected.

Red/green flashing alternately

Detect a communication error between SI unit and I/O unit.

Red ON

SI unit has failed.

Содержание EX600-DXPD 16 Series































































Результаты поиска

Содержание EX600-DXPD 16 Series

Отзывы:

Похожие инструкции для EX600-DXPD 16 Series

Бренды по названию

Популярные бренды

SMC Networks EX600-DXPD 16 Series, Руководство по эксплуатации

Результаты поиска

Содержание EX600-DXPD 16 Series

Отзывы:

Похожие инструкции для EX600-DXPD 16 Series

Бренды по названию

Популярные бренды