SMC Networks EX600-DXPD 16 Series страница 15 Скачать руководство пользователя

Страница: 15 / 62

-14-

No.EX

※※

-OMU1021-A

SI Unit

Model Indication and How to Order

EX600- S EN 5

-X16

SI Unit

Output type / Number of ports

Symbol

Content

Protocol

PNP (negative common) / 2port

Symbol

Content

EtherNet/IP

Summary of Product parts

No.

Description

Function

Status display LED

Displays the status of the unit.

Display cover

Open at the switch configuration.

Display cover tightening screw

Loosen to open the display cover.

Connector (BUS OUT)

Connects the cable for fieldbus outputs.
(M12, 5 pin, socket: SPEEDCON)

Marker groove

Groove to mount a marker.

Connector (PCI)

Connects the cable of the handheld terminal.
(M12, 5 pin, socket: SPEEDCON)

Valve plate mounting screw hole

Fixes the valve plate.

Valve plate mounting groove

Groove to insert the valve plate into.

Joint bracket

Bracket for joining to adjacent units.

Unit connector (plug)

Transmits signals and power supplies to adjacent units.

Connector (BUS IN)

Connects the cable for fieldbus inputs.
(M12, 5 pin, socket: SPEEDCON)

Seal cap (2 pcs.)

Mounted on to unused connectors (BUS OUT and PCI).

Содержание EX600-DXPD 16 Series































































Результаты поиска

Содержание EX600-DXPD 16 Series

Отзывы:

Похожие инструкции для EX600-DXPD 16 Series

Бренды по названию

Популярные бренды

SMC Networks EX600-DXPD 16 Series, Руководство по эксплуатации

Результаты поиска

Содержание EX600-DXPD 16 Series

Отзывы:

Похожие инструкции для EX600-DXPD 16 Series

Бренды по названию

Популярные бренды