SMC Networks EX600-DXPD 16 Series страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 62

background image

-13-

No.EX

※※

-OMU1021-A

■

Wiring

•Connect the M12 or M8 connector cable.

M12 connector is applicable for SPEEDCON connector.

SPEEDCON connector wiring method is explained

below.
(1) Align the mark B on the metal bracket of the cable side connector (plug/socket) with the mark A.
(2) Align the mark C on the unit and insert the connector into the unit vertically.

If they are not aligned, the connector cannot be joined properly.

(3) When the mark B of the connector has been turned 180 degrees (1/2 turn), wiring is completed.

Confirm that the connection is not loose. If turned too far, it will become hard to remove the connector.

(1)

(2)

(3)

•Mounting the marker

Signal name of the input or output devices and unit address can be written to the marker, and it can be
installed to each unit.
Mount the marker (EX600-ZT1) into the marker groove as required.

«
...
12
13
14
15
16
...
»

Содержание EX600-DXPD 16 Series































































Отзывы:

Нет отзывов

Похожие инструкции для EX600-DXPD 16 Series

Бренд: ACS Страницы: 56

Бренд: Oberheim Страницы: 40

Бренд: idiag Страницы: 12

Бренд: PANDROL Страницы: 36

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

BOMAG BW 100 ADM-5

Бренд: Fayat Страницы: 216

Бренд: B medical systems Страницы: 28

Бренд: Tascam Страницы: 8

Бренд: PAT Страницы: 44

Бренд: Park Tool Страницы: 4

Бренд: Qlight Страницы: 4

Бренд: Radial Engineering Страницы: 16

Бренд: R&S Страницы: 61

Бренд: ICS Страницы: 156

Бренд: Ignis Pixel Страницы: 4

Бренд: Faro Страницы: 161

Бренд: Hatco Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды