manualshive.com logo in svg

SMC Networks EX600-AX, Руководство по эксплуатации

Поделиться
Скачать
SMC Networks EX600-AX Скачать руководство пользователя страница 46

 

 
 

 

- 46 - 

No.EX##-OML0007  

             

 

 

 

Troubleshooting

 

 
Please refer to the following flowchart if a fault occurs on the fieldbus system.   

 

Error status is reflected by the parameter settings of a fieldbus system.     

 

When a fault occurs, please refer to the troubleshooting and the parameter setting sections of this manual, 
to ensure the appropriate action is taken. 

 

If the cause of the fault cannot be confirmed, it is possible that the equipment may have failed. When 
failure of fieldbus system equipment occurs, it is possible that the error was caused by the system 
requirements. If that is the case, please consider the counter-measures accordingly. 

   

   

   

   

   

   

Yes

 

   

No 

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

Fieldbus system 

does not operate 

normally 

Model selection 

or protocol 

version is wrong

Wrong selection

Fault No.7 

SI unit’s LED 

indicates error 

ST(M) LED 

is blinking 

green

Digital input unit 

LED indicates 

error 

Fault No.1 

Digital output unit 

LED indicates 

error 

Fault No.2 

Manifold or unit is 

damaged 

Fault No.3 

Fault No.4 

Manifold or unit is 

damaged 

Unit other than SI 

unit LED indicates 

error 

Solenoid valve does not 

operate normally 

Digital input equipment does 

not operate normally 

Fault No.5 

Fault No.6 

Fault No.8 

Fault No.9 

Analog input unit 

LED indicates 

error 

Digital output equipment 

does not operate normally 

 Analogue input equipment 

does not operate normally 

Содержание EX600-AX










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды