SMC Networks EX260-SEN2-X205 Скачать руководство пользователя страница 17

Страница: 17 / 48

-16-

No.EX

※※

-OMX1001

LED Indication and Settings

○LED indication

LED

LED Status

Description

OFF

The SI unit operating voltage is not supplied or the IP address is not set.

Green ON

EtherNet/IP

communications established.

Green flashing

EtherNet/IP

communications not established.

Red flashing

EtherNet/IP

communications time out.

Red ON

IP address duplicated.

OFF

The SI unit operating voltage is not supplied.

Green ON

Operating normally.

Green flashing

Either of the following conditions are detected.
•The unit has not been configured correctly.
•The master is idle state.

Red flashing

Recoverable error.

Red ON

Unrecoverable error.

L/A1

OFF

BUS IN side: No Link, No Activity

Green ON

BUS IN side: Link, No Activity

Green flashing

BUS IN side: Link, Activity

L/A2

OFF

BUS OUT side: No Link, No Activity

Green ON

BUS OUT side: Link, No Activity

Green flashing

BUS OUT side: Link, Activity

PWR(V)

Yellow ON

Load voltage for the valve is supplied

OFF

Load voltage for the valve is not supplied or is outside the tolerance range
(19 V or less)

Содержание EX260-SEN2-X205

















































Результаты поиска

Содержание EX260-SEN2-X205

Отзывы:

Похожие инструкции для EX260-SEN2-X205

Бренды по названию

Популярные бренды

SMC Networks EX260-SEN2-X205, Руководство по эксплуатации

Результаты поиска

Содержание EX260-SEN2-X205

Отзывы:

Похожие инструкции для EX260-SEN2-X205

Бренды по названию

Популярные бренды