Smawave Technology SGL4010 Скачать руководство пользователя страница 12

Страница: 12 / 54

software version file.

3. Click

Open

. The dialog box choses. The save path and name of the target software version

file are displayed in the Update file field.

4. Click

Submit

5. The software upgrade starts. After the upgrade, the CPE automatically restarts and runs the

new software version. As shown in Figure 4-2.

During an upgrade, do not power off the CPE or disconnect it from the
computer.

Figure 4-2

4.2Auto upgrade

To perform a ftp auto upgrade successfully, make sure the CPE is connected to the Internet.

To perform a ftp auto upgrade, perform the following steps:

Choose

Update

Auto upgrade

Enable

auto upgrade

If you want to check new firmware after connect to Internet, you need to

enable the item of

Check new firmware after connect to Internet

Set a ftp address to the

Upgrade folder

box.

Set

Version file

Set

User name

and

Password

Set the

Interval

of checking new firmware.

Set

Start time

Set

Random time

Click

Submit

. As shown in Figure 4-3.

The CPE will automatically upgrade according to the setting. During an upgrade,
do not disconnect the power supply or operate the CPE.

Содержание SGL4010























































Результаты поиска

Содержание SGL4010

Отзывы:

Похожие инструкции для SGL4010

Бренды по названию

Популярные бренды

Smawave Technology SGL4010, Руководство пользователя

Результаты поиска

Содержание SGL4010

Отзывы:

Похожие инструкции для SGL4010

Бренды по названию

Популярные бренды