background image

                                                                           

 

HRC200 Industrial Remote Control User Manual                                                                          Page 10 of 16

 

Method 

Process 

4.

 

If  pairing  successfully  within  60s,  remote  control  COMM  indicator 

extinguishes after illuminating green 2s, receiver LoRa and RS485 indicators 
extinguish, POWER indicator keeps green for a long time. Otherwise, COMM 
indicator keeps red for a long time when the pairing fails. 

Method 2:   
Receiver  waits  for 
remote 

control 

pairing. 

1.

 

Turn  the  remote  control  and  receiver  to  the  same  channel.  (see  the 

communication channel configuration, default channel is 515MHz.) 

2.

 

Turn  on  the  receiver  power,  POWER  indicator  keeps  on.  Insert  a  slender 

needle  less  than  3.5mm  in diameter  into the  PAIR hole  vertically, then  long 
press  PAIR  key  6s,  LoRa,  RS485  and  POWER  indicator  flash  green.  Press 
PAIR key again during LoRa pairing can cancel pair. 

3.

 

Turn  on  the  remote  control  power,  its  power  indicator  keeps  on.  Long 

press F2 key 6s. 

4.

 

If  pairing  successfully  within  60s,  remote  control  COMM  indicator 

extinguishes after illuminating green 2s, receiver LoRa and RS485 indicators 
extinguish, POWER indicator keeps green for a long time. Otherwise, COMM 
indicator keeps red for a long time when the pairing fails. 

4.5

 

RS485 INTERFACE 

Receiver  connects  to  engine  controller  via  RS485  interface,  120Ω  terminal  matching  resistor  is 

recommended to use (when RS485  A(+) and TR terminal is short connected), RS485 communication 
line must use twisted shielded pair line.

 

 

Fig.4 RS485 Connection Diagram 

 
 
 
 
 
 
 
 
 
 

Содержание HRC200

















Отзывы: