SMART 6806800K30J Скачать руководство пользователя страница 39

Страница: 39 / 50

Functional Description

RTM-ATCA-F125 Installation and Use (6806800K30J)

4.3.2

Front-Blade Port Mapping

The four SFP sites are connected to the front-blade base switch according to the following
table..

4.3.3

SFP Connection

The SFP sites allow the fitting of a wide range of third-party SFP modules to support
1000Base-T, long and short range optical connection. Refer to the ATCA-F125 Installation
and Use Manual for a list of SFP devices tested with this product.

The following table shows the SFP connector pin assignments.

Table 4-4

Front-Blade Port Mapping

RTM Port

Front Blade Base Switch Port

ETH1

ge20

ETH2

ge21

ETH3

ge22

ETH4

ge23

Table 4-5

SFP Connector Pin Assignment

Pin

Signal

Pin

Signal

GND

TX_FAULT

RX-

TX_DISABLE

RX+

I2C_SDA

GND

I2C_SCL

VCCr (+3.3V)

MOD_ABS

VCCt (+3.3V)

RATE_SEL

GND

LOS

TX+

GND

TX-

GND

Содержание 6806800K30J



















































Результаты поиска

Содержание 6806800K30J

Отзывы:

Похожие инструкции для 6806800K30J

Бренды по названию

Популярные бренды

SMART 6806800K30J, Инструкция по установке и использованию

Результаты поиска

Содержание 6806800K30J

Отзывы:

Похожие инструкции для 6806800K30J

Бренды по названию

Популярные бренды