WES-111/WES-115 I.I. — Rev. 0a (11/05)
Code No. 0816555
INSTALLATION INSTRUCTIONS FOR
DUAL-FLUSH FLUSHOMETERS
LIMITED WARRANTY
Sloan Valve Company warrants its UPPERCUT™ Dual-Flush Flushometers to be made of first class materials, free from defects of material or
workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly
installed and serviced, for a period of three years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company
will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and
this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This
warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose
of resale.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
PRIOR TO INSTALLATION
Before you install the Dual-Flush Flushometer, be sure
the items listed below are installed. Also, refer to the
rough-in diagram below.
• Closet fixture
• Drain line
• Water supply line
Important:
• ALL PLUMBING SHOULD BE INSTALLED IN
ACCORDANCE WITH APPLICABLE CODES AND
REGULATIONS.
• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE
AN ADEQUATE VOLUME OF WATER FOR EACH
FIXTURE.
• FLUSH ALL WATER LINES PRIOR TO MAKING
CONNECTIONS.
The Sloan Dual-Flush Flushometer is designed to
operate with 10 to 100 psi (69 to 689 kPa) of water
pressure. THE MINIMUM PRESSURE REQUIRED TO THE
VALVE IS DETERMINED BY THE TYPE OF FIXTURE
SELECTED. Consult fixture manufacturer for minimum
pressure requirements.
Most Low Consumption water closets (1.6 gpf/6.0 Lpf)
require a minimum flowing pressure of 25 psi (172 kPa).
TOOLS REQUIRED FOR INSTALLATION
• Straight blade screwdriver
• Sloan A-50 Super-Wrench™, Sloan A-109 Plier
Wrench or smooth jawed spud wrench
SLOAN VALVE COMPANY • 10500 Seymour Avenue • Franklin Park, IL 60131
Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380
www.sloanvalve.com
Copyright © 2005 SLOAN VALVE COMPANY
Printed 11-05
WES-115
Exposed Closet Flushometer
for 1-1/2 Top Spud
WES-111
Exposed Closet Flushometer
for 1-1/2 Top Spud
VALVE ROUGH-IN
VANDAL RESISTANT CONTROL STOP CAP REMOVAL
Use a large flat screwdriver as a lever to remove the Cap from the
Control Stop. Insert the screwdriver blade between the bottom
edge of the Cap and the flat surface of the Control Stop body as
shown. Push the screwdriver handle straight back toward the
wall to gently lift the Cap. If necessary, work the
screwdriver around the diameter of the Cap until you can
grasp the Cap and lift it completely off the Sleeve. The
Sleeve should remain attached to the bonnet of the Control Stop.
CARE AND CLEANING OF CHROME AND SPECIAL FINISHES
DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean
Flushometers that may dull the luster and attack the chrome or special decorative
finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel.
While cleaning the bathroom tile, protect the Flushometer from any splattering of
cleaner. Acids and cleaning fluids will discolor or remove chrome plating.
TROUBLESHOOTING GUIDE
1. Flushometer does not function (no flush).
A. Control Stop or Main Valve is Closed. Open Control Stop or Main Valve.
B. Handle Assembly is damaged. Replace Handle (WES-212).
C. Relief Valve is damaged. Replace Performance Kit.
2. Volume of water is not sufficient to siphon fixture.
A. Control Stop is not open wide enough. Adjust Control Stop for desired delivery
of water volume.
B. Dual Filtered Diaphragm Assembly is damaged. Replace Performance Kit.
C. Incorrect Dual Filtered Diaphragm Assembly is installed in Flushometer; for
instance, Urinal assembly inside a Closet Flushometer, or Low Consumption
assembly inside a higher consumption fixture. Determine the flush volume
required by the fixture and replace Performance Kit. Use valve label and
markings on fixture for reference.
D. Water supply volume or pressure is inadequate. If no gauges are available to
properly measure supply pressure or volume of water at the Flushometer, then
remove the Relief Valve from the Dual Filtered Diaphragm Assembly,
reassemble the Flushometer and completely open the Control Stop.
• If the fixture siphons, more water volume is required. Install a higher
flushing volume Performance Kit. IIM
MP
PO
OR
RTTA
AN
NTT —
— LLaaw
wss aanndd R
Reegguullaattiioonnss
rreeqquuiirriinngg LLoow
w C
Coonnssuum
mppttiioonn FFiixxttuurreess ((1
1..6
6 ggppff//6
6..0
0 LLppff W
Waatteerr C
Clloosseettss aanndd 1
1..0
0
ggppff//3
3..8
8 LLppff U
Urriinnaallss)) pprroohhiibbiitt tthhee uussee ooff hhiigghheerr fflluusshhiinngg vvoolluum
meess..
• If the fixture does not siphon or if a Low Consumption flush is required,
steps must be taken to increase the water supply pressure and/or volume.
Contact the fixture manufacturer for minimum water supply requirements of
the fixture.
3. Length of flush is too short (short flush).
A. Dual Filtered Diaphragm Assembly is damaged. Replace Performance Kit.
B. Handle Assembly is damaged. Replace Handle (WES-212).
C. Incorrect Dual Filtered Diaphragm Assembly is installed in Flushometer; for
instance, Urinal assembly inside a Closet Flushometer, or Low Consumption
assembly inside a higher consumption fixture. Determine the flush volume
required by the fixture and replace Performance Kit. Use valve label and
markings on fixture for reference.
4. Length of flush is too long (long flush) or continuous.
A. Metering bypass hole in Diaphragm is clogged. Remove the Dual Filtered
Diaphragm Assembly. Remove the Primary and Secondary Filter Rings from the
Diaphragm and wash under running water. Replace Performance Kit if cleaning
does not correct the problem.
B. Diaphragm or Relief Valve is damaged. Replace Performance Kit.
C. Incorrect Dual Filtered Diaphragm Assembly is installed in Flushometer; for
instance, Closet assembly inside a Urinal Flushometer, or Water Saver
assembly inside a Low Consumption Flushometer. Determine the flush volume
required by the fixture and replace the Performance Kit. Use valve label and
markings on fixture for reference.
D. Inside Cover is damaged. Replace Inside Cover (A-71).
E. Supply line water pressure has dropped and is not sufficient to close the valve.
Close Control Stop until pressure is restored.
5. Chattering noise is heard during flush.
A. Inside Cover is damaged. Replace Inside Cover (A-71).
6. Handle Leaks.
A. Handle Seal or Assembly is damaged. Replace Handle (WES-212).
When assistance is required, please contact Sloan Valve Company Installation
Engineering Department at:
1-888-SLOAN-14 (1-888-756-2614) OR 1-847-233-2016
PARTS LIST
1
3
IItteem
m
P
Paarrtt
D
Deessccrriippttiioonn
N
Noo..
N
Noo..
1
†
Valve Assembly
2
WES-212
ADA Compliant Dual-Flush Handle Assembly
3
H-700-A
Bak-Chek
®
Control Stop
4
V-600-AA
1-1/2" (38 mm) x 9" (229 mm) Vacuum Breaker Assembly ‡
5
F-5-A
1-1/2" (38 mm) Spud Coupling Assembly
6
H-633-AA
1" (25 mm) Sweat Solder Kit with Cast Set Screw Flange
†
Part number varies with valve model variation; consult factory.
‡
Length varies with valve model variation; consult factory.
For a complete listing of Flushometer Valve components and Repair Kits, see
Maintenance Guide or consult your nearest Plumbing Wholesaler.
For optimum water conservation and Flushometer performance, use only Genuine
Sloan Parts.
Manufactured in the U.S.A. by Sloan Valve Company under one or more of the
following patents: U.S. Pats. 5,295,655; 5,505,427; 5,542,718; 5,558,120;
5,564,460; 5,649,686; 5,730,415. Other Pats. Pending. BAK-CHEK
®
, PARA-FLO
®
,
PERMEX
®
, TURBO-FLO
®
, DUAL FILTERED DIAPHRAGM™. Additional patent(s)
pending.
N
NO
OTTIIC
CEE::
The information contained in this document is subject to change without notice.
2
6
5
4
Protect the chrome or special finish of Sloan Flushometers — DO
NOT USE toothed tools to install or service these valves. Use a
Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth
jawed spud wrench to secure all couplings. Also see “Care and
Cleaning” section of this manual.
!!! IMPORTANT !!!
When mounted on an ADA accessible bowl, the rough-in to the
supply inlet should be no higher than 37½” or the handle will
exceed maximum height allowances under ADA guidelines.
New ADAAG Guidelines allow for Split or Offset Grab Bars, check
with local authorities or reference section 604.5.2 of ADAAG.
!!! IMPORTANT !!!
This product contains mechanical and/or electrical components
that are subject to normal wear. These components should be
checked on a regular basis and replaced as needed to maintain
the valve’s performance.
!!! IMPORTANT !!!
