manualshive.com logo in svg

SkyWave IDP 800 Series, Руководство по оборудованию, Страница: 9 / 102

Поделиться
Скачать
SkyWave IDP 800 Series Скачать руководство пользователя страница 9

 

IDP 800 Terminal Series - Hardware Guide 

© SkyWave Proprietary                                                    ix                                                   T209, Version 01 

Preface 

Purpose 

This document is as an overview of the installation procedures and hardware 
characteristics and specifications for the IDP 800 series of terminals. 

Audience 

This document is for technical readers. It provides information to ensure successful 
installation and operation of IDP 800 series terminals. 

Errata Sheet 

Refer to the SkyWave Customer Support website for a possible Errata Sheet available 
after the release of this document. Always check the site for the most current 
documentation releases. 

Notation  

Hardware components and hardware labels in this document may not be exactly as shown 
and are subject to change without notice. 

CAUTION

 

This safety symbol warns users of possible hazards to personnel, 
to equipment, or to both. It includes hazards that will or can 
cause severe personal injury, death, or substantial property 
damage if the hazard is not avoided; and hazards that will or can 
cause minor personal injury or property damage if the hazard is 
not avoided. 

Note:

 

A note indicates information with no potential hazard, but the user should 
make special note. A note is also used to indicate points of interest or to provide 
supplementary information about a feature or task. 

Numbered lists indicate a series of steps required to complete a task or function.  

Bulleted lists highlight information where order or sequence is not crucial. 

Reference 

The content of the following documents may be useful in conjunction with this guide. 
These documents are available from the IDP Developer Toolkit or 

support.skywave.com

. 

[T202]   

IDP 600 and IDP 800 Terminal Series API Reference Guide 

[T204]   

IDP Terminal User Guide 

Battery Safety Warnings 

CAUTION

 

Replace depleted batteries only with the batteries specified in 
Section 3.8.1. Do not use any other battery chemistry. 

Содержание IDP 800 Series







































































































Отзывы:

Нет отзывов