SkyWave IDP 800 Series Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 102

SkyWave IDP 800 Series Скачать руководство пользователя страница 52

IDP 800 Terminal Series - Hardware Guide

T209, Version 01 40 © SkyWave Proprietary

4.2.4 Required Materials

You require the following materials to install a terminal. These materials do not ship with
the terminal.



Qty 6 - M4 (8-32) 18-8 stainless steel screws (length depends on mounting
surface thickness)



Qty 6 - M4 (8-32) nuts with 18-8 stainless steel flat and lock washers



Waterproof sealing tape



Qty 1 - Custom cable

SkyWave recommends that the Solution Provider supply the end-user with a custom built
cable.

4.2.5 Required Tools

You require the following tools to install a terminal.



Drill



4.5 mm drill bit



#2 Phillips torque screwdriver



Socket wrench set

4.3 Determine a Suitable Mounting Location

Before installing the terminal, consider the important guidelines provided below.

CAUTION

Most users install the terminals on a vehicle. It is very important
for installers to install the terminals in a safe and secure way to
avoid danger or damage to persons or property.



Mount the terminal on a flat surface for mobile installations such that the elevation
angle does not change with rotation.



For fixed installations ensure that the antenna is pointing towards the equator, facing
south if in the Northern Hemisphere and facing north if in the Southern Hemisphere,
and its line of sight to the sky (satellite) is clear of obstructions.



For a mobile installation, mount the antenna at the highest point on the vehicle or
vessel where it has a clear view of the sky (satellite) in all directions



Fasten the terminal securely so that it is not loose and does not move easily.



Mount the terminal on a rigid, flat, stable surface. If necessary, use a mounting
bracket or other suitable support.



Mount the terminal so that the top surface is horizontal (flat). Failure to do so may
compromise line of sight between the satellite and the terminal.



Ensure that the terminal is pointing towards the equator and its line of sight to the sky
(satellite) is clear of obstructions.

«
...
50
51
52
53
54
...
»

Содержание IDP 800 Series







































































































Отзывы:

Нет отзывов