manualshive.com logo in svg
  • Главная
  • /
  • Skyjack
  • /
  • SJ-7027
  • /
  • Руководство по эксплуатации, техническому обслуживанию и каталог запасных частей

Skyjack SJ-7027, Руководство по эксплуатации, техническому обслуживанию и каталог запасных частей


Поделиться
Скачать
background image

SECTION 5, Page 10

                                                                                SJ-600 Series Engine Powered

 112715

June 2001

WHEEL BOLT/NUT INSPECTION AND TORQUING PROCEDURE

It is necessary to check the torque on all wheel nuts and wheel bolts at pre-delivery, after 8 hours of operation and
at weekly intervals using the following procedure:

1.

Confirm that each wheel fastener is torqued to 140 ft. lbs. (± 5 ft. lbs.) using a suitable torque wrench of
known accuracy.  If any fastener falls outside of the specified tolerance, ALL fasteners MUST be torqued
using the tightening sequence shown in Figure 5-5.

Figure 5-5.  Wheel Fastener Tightening Sequence

2.

Again, confirm that each wheel fastener is torqued to the specified tolerance.  Retorque as necessary until
ALL fasteners are properly torqued.

WHEEL REINSTALLATION AND TORQUING PROCEDURE

When a Wheel/Tire Assembly has been removed or replaced, it will be necessary  to follow the procedure below to
ensure proper installation:

1.

Inspect wheel fastener threads for damage of defects.  Replace if defective.

2.

Clean the mounting surfaces of the hub and wheel rim of debris, rust, excess paint, etc.

3.

Mount wheel on the hub, centering mounting holes on the wheel studs or bolt holes.  Use appropriate lifting
device as required.

4.

Install the wheel nuts or wheel bolts and hand tighten to center the rim.

5.

Tighten the nuts or bolts to approximately 50 ft. lbs. torque using the tightening sequence in Figure 5-5.
above.

6.

Tighten to 100 ft. lbs. using the same sequence.

7.

Tighten to 140 ft. lbs. using the same sequence.

8.

Repeat the tightening sequence to confirm that none have changed from 140 ft. lbs.  If any are found below
140 ft. lbs., repeat complete sequence until there is no change in torque values.  If possible, drive the
machine prior to checking torques.

9.

Check torque values after 8 hours of operation and then at weekly intervals.

Содержание SJ-7027

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SJ-7027

Dannmar DLR-6 Installation And Operation Manual preview
DLR-6
Бренд: Dannmar Страницы: 40
BendPak MD-6XP Installation And Operation Manual preview
MD-6XP
Бренд: BendPak Страницы: 44
BendPak XR-12000 Installation And Operation Manual preview
XR-12000
Бренд: BendPak Страницы: 44
Terex Genie Z-45 BE Operator'S Manual preview
Genie Z-45 BE
Бренд: Terex Страницы: 65
Titan Lifts MRL-6000 Installation, Operation & Maintenance Manual preview
MRL-6000
Бренд: Titan Lifts Страницы: 20
Sinoboom GTJZ1412 Operation Manual preview
GTJZ1412
Бренд: Sinoboom Страницы: 23
Sinoboom GTBZ26 Service Manual preview
GTBZ26
Бренд: Sinoboom Страницы: 59
Sinoboom GTJZ0612E Maintenance Manual preview
GTJZ0612E
Бренд: Sinoboom Страницы: 94
Snorkel S2770BE Repair Parts Manual preview
S2770BE
Бренд: Snorkel Страницы: 217

Бренды по названию

Популярные бренды

Загрузить еще бренды