manualshive.com logo in svg
  • Главная
  • /
  • Skyjack
  • /
  • SJ-7027
  • /
  • Руководство по эксплуатации, техническому обслуживанию и каталог запасных частей

Skyjack SJ-7027, Руководство по эксплуатации, техническому обслуживанию и каталог запасных частей


Поделиться
Скачать
background image

SECTION 5, Page 2

                                                                                   S

J-600 Series Engine Powered

 

112715

June 2001

OPERATOR’S RESPONSIBILITY FOR
MAINTENANCE

Death or injury can result if the work platform is not kept
in good working order. Inspection and maintenance
should be performed by competent personnel who are
familiar with mechanical procedures.

The operator should be assured that the work platform
has been properly maintained before using it. Included
in this section is information on lubrication and
inspection points that require maintenance.

Even if the operator is not responsible for the
maintenance of this work platform, the operator should
perform the daily inspections found in 

Table 2-

4

.

Maintenance and Inspection Schedule

.

IMPORTANT NOTE

Replace all worn or damaged parts or labels
discovered during this inspection. Any problems or
malfunctions that may affect the safe operation of this
work platform MUST be repaired immediately.

      

    

DANGER

CRUSHING HAZARD

DO NOT

 

reach through scissors assembly without the

safety bar properly positioned.  

Failure to avoid this

hazard will result in death or serious injury

!

MAINTENANCE AND INSPECTION
SCHEDULE

The actual operating environment of the work platform
governs the use of the maintenance schedule.  The
inspection points covered in

 Table 2-

4

. Maintenance

and Inspection Schedule

 indicates the areas of the

work platform to be checked and the intervals at which
they should be checked.

OWNER’S ANNUAL INSPECTION
RECORD

It is the responsibility of the owner to arrange daily,
weekly, monthly and annual inspections of the work
platform.  

Table 2-1.  Owner’s Annual Inspection Record

in section 2 is to be used for recording the date of
inspection, owner’s name and the person responsible
for the inspection of this work platform.

GENERAL MAINTENANCE HINTS

•

Before attempting any repair work, disconnect
battery ground negative (-) lead.

•

Properly position safety bar if the scissors
assembly is raised.

•

Preventive maintenance is the easiest and least
expensive type of maintenance.

Содержание SJ-7027

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SJ-7027

POP UP PUSH 10 PRO Operator'S Safety And Maintenance Handbook preview
PUSH 10 PRO
Бренд: POP UP Страницы: 20
Castex QJY3.2-1 Operation Manual preview
QJY3.2-1
Бренд: Castex Страницы: 17
ALMAC AlmaCrawler JIBBI 1250 EVO Translation Of Original Instructions preview
AlmaCrawler JIBBI 1250 EVO
Бренд: ALMAC Страницы: 233
Power Towers nano SP Operating And Maintenance Manual preview
nano SP
Бренд: Power Towers Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды