Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 56

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 Скачать руководство пользователя страница 8

4O3A Signature – Antenna Genius User Manual

Page

7

of

55

4.

WHAT CAN ANTENNA GENIUS

tm

DO?

Antenna Genius

tm

8x2 v2 Plus is a matrix antenna switch which can route eight antennas to two

radios using a variety of control methods. Software and hardware interlocks - double protection
- prevent the same antenna from being connected to both radios. This, along with AG’s ultra-
high port-to-port isolation help protect your radios from front end damage.

AG in action with SmartSDR @ 4O3A (

AG Always on top

option engaged)

4.1.

Multiple control options

You have five ways to control your AG:

1.

FlexRadio over your TCP/IP network; AG will automatically follow two different Slice
band selections and obtain band data from them

2.

Manual band switching from the AG Windows app connected via your network

3.

Interface Genius

tm

(IG) connected to your radio(s) via a USB or serial port and connected

to AG via LAN; IG will connect to pretty much any modern radio via its serial or USB CAT
port

4.

BCD (Binary-Coded Decimal) signals via the DE-15 VGA-style connector

5.

+12 VDC “Pin-to-Port” via the DE-15 VGA-style connector

4.2.

SO2R and multi-op with a single FLEX-6000

AG’s extreme port-to-port isolation is perfect for SO2R (Single Operator 2 Radio) contesting with
a single Flex rig! With AG, you can operate SO2R with one radio using a single FLEX-6600 or
FLEX-6700 transceiver in full duplex mode. In other words, the ‘two radios’ in SO2R are both

«
...
6
7
8
9
10
...
»

Содержание 4O3A Signature Antenna Genius 8x2 Plus v2

























































Отзывы:

Нет отзывов