manualshive.com logo in svg

Skope B550-2, Руководство пользователя

Поделиться
Скачать
Skope B550-2 Скачать руководство пользователя страница 13

13

SKOPE B550/660-2 and BME550-2

Servicing

User Manual

Cleaning

When necessary, wipe the interior and exterior of the cabinet with a damp 
cloth. Ensure the cabinet is disconnected from the mains power supply 
before cleaning. Periodic cleaning of the condenser coil is also 
recommended.

 Condenser

coil

The condenser coil MUST be kept clean for efficient and reliable operation. 
Clean the condenser coil with a brush and vacuum cleaner regularly. The 
condenser coil is located behind a side baffle, on the right hand side of the 
refrigeration unit.

To access the condenser coil

1. Isolate the cabinet from the mains power supply and remove the front 

kick panel (see “Isolating Electrics” on page 12).

2. Remove the cabinet wiring junction box by loosening both the end 

keyhole fixing screws.

3. Remove the two screws holding the side baffle to the condenser coil 

and carefully pull the baffle out from the unit.

4. The condenser coil can now be accessed for cleaning. Clean the 

condenser coil with a brush and vacuum cleaner.

5. Refit the side baffle and cabinet wiring junction box.

6. Refit the cabinet kick panel.

7. Reconnect the cabinet to the mains power supply.

Caution:

Disconnect the cabinet from the mains power supply before cleaning 

the condenser coil.

Содержание B550-2
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды