manualshive.com logo in svg

Skoda Rapid NH 2014, Руководство по ремонту


Поделиться
Скачать
background image

❑ 5.2 Nm.

4 - Retaining clip
5 - Retaining clip

3.17.2

Removing and installing head airbag

with ignition for head airbag driver's

side/front passenger side - N251 - / -

N252 -

Removing

WARNING

♦ Observe the safety instructions for pyrotechnic compo‐

nents

⇒ “3.3 Observe the general safety instructions for working

on airbag, belt tensioner and battery separation units (py‐

rotechnical components)”, page 225

 .

♦ Observe the additional safety instructions for the head air‐

bag

⇒ “3.4 Special instructions for driver and front passenger

airbag”, page 226

 .

♦ Observe the disposal instructions for pyrotechnic compo‐

nents

⇒ “3.5 Storage, transport and disposal of airbag, belt ten‐

sioner and battery separation units (pyrotechnical com‐

ponents)”, page 226

 .

– Turn off the ignition and disconnect the battery earth strap ⇒ 

Electrical System ; Rep. gr.  27 ; Disconnecting and recon‐

necting the battery .

– Lower the moulded headliner (not necessary to remove from

the vehicle)

⇒ “7.1 Removing and installing moulded headliner”,

page 282

 .

– Remove clips -4- from the head airbag.
– Use e.g. a set of pointed pliers for unclipping. Insert the pliers

-5- into openings -1 and 2-. Press gently until the catches -3-

are clear.

– Slide the clips out of the body.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

240

     Rep. gr.69 - Passenger protection

Содержание Rapid NH 2014
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid NH 2014

Feniex AM600 Instruction Manual preview
AM600
Бренд: Feniex Страницы: 6
Kargo Master 80070 Assembly Lnstructions preview
80070
Бренд: Kargo Master Страницы: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Бренд: Kargo Master Страницы: 21
Kargo Master 40201 Installation Manual preview
40201
Бренд: Kargo Master Страницы: 4
Fab Fours BLACK STEEL S2560 Installation Instructions Manual preview
BLACK STEEL S2560
Бренд: Fab Fours Страницы: 9
Suzuki Movano Owner'S Manual preview
Movano
Бренд: Suzuki Страницы: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Бренд: Torklift Страницы: 16
Alpine eX-10 Installation Manual preview
eX-10
Бренд: Alpine Страницы: 8
Mobile Create MCM3 Instruction Manual preview
MCM3
Бренд: Mobile Create Страницы: 15
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Бренд: Mazdaspeed Страницы: 8
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Бренд: Mazda Страницы: 12
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
Boyo VTL17LTJ Manual preview
VTL17LTJ
Бренд: Boyo Страницы: 9
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Бренд: Safe Fleet Страницы: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Бренд: Honda Страницы: 4
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Бренд: Honda Страницы: 124
r.LiNK RL2-NBT Manual preview
RL2-NBT
Бренд: r.LiNK Страницы: 20
Jaeger 21010508J Fitting Instructions Manual preview
21010508J
Бренд: Jaeger Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды