manualshive.com logo in svg

Skoda Rapid NH 2014, Руководство по ремонту


Поделиться
Скачать
background image

1.2.2

Removing interior rear-view mirror with

rain and light detector sensor

Removing
– Switch off the ignition and all electrical components.
– Unclip cable cover -2-.
– Unclip cover -4- from the retaining plate.
– Turn mirror -3- 20° anticlockwise.
– Remove mirror -3- from retaining plate -5-.
– Disconnect connector -1- from plug connection.
Installing
– Insert connector -1- into plug connection.
– Turn mirror -3- 20° anticlockwise and position to retaining plate

-5-.

– Ensure the mirror is seated parallel and turn clockwise until it

locks into place.

– Install cap -4-.

– Install cable cover -2-.
Removing retaining plate for interior mirror with sensor for rain

and light detection

Note

The retaining plate for interior mirror with sensor for rain and light

detection cannot be glued on under workshop conditions. Is part

of the windscreen.

1.3

Glueing the retaining plate for the interi‐

or rear-view mirror

1.3.1

Materials

♦ Glass metal adhesive kit - D 000 703 A1-

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Interior rear-view mirror    

199

Содержание Rapid NH 2014
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid NH 2014

N-Com B3 User Instructions And Safety preview
B3
Бренд: N-Com Страницы: 28
Cadillac SRX 2012 Instructions preview
SRX 2012
Бренд: Cadillac Страницы: 3
Cadillac Escalade 2021 Features Manual preview
Escalade 2021
Бренд: Cadillac Страницы: 12
Cadillac CTS 2008 Navigation System Owner'S Manual preview
CTS 2008
Бренд: Cadillac Страницы: 106
Cadillac CTS 2008 Customer Convenience/Personalization Manual preview
CTS 2008
Бренд: Cadillac Страницы: 20
Cadillac ATS 2014 Convenience/Personalization Manual preview
ATS 2014
Бренд: Cadillac Страницы: 20
Cadillac ATS 2013 Owner'S Manual preview
ATS 2013
Бренд: Cadillac Страницы: 326
Cadillac CTS 2012 Quick Manual preview
CTS 2012
Бренд: Cadillac Страницы: 28
Cadillac ESCALADE - BROCHURE 2009 Owner'S Manual preview
ESCALADE - BROCHURE 2009
Бренд: Cadillac Страницы: 602
Cadillac ESCALADE ESV 2004 Owner'S Manual preview
ESCALADE ESV 2004
Бренд: Cadillac Страницы: 20
Cadillac ESCALADE EXT 2005 Owner'S Manual preview
ESCALADE EXT 2005
Бренд: Cadillac Страницы: 460
Cadillac CT6 SUPER CRUISE 2018 Convenience/Personalization Manual preview
CT6 SUPER CRUISE 2018
Бренд: Cadillac Страницы: 8
Cadillac XT6 2023 Manual preview
XT6 2023
Бренд: Cadillac Страницы: 20
Cadillac LYRIQ 2023 Owner'S Manual preview
LYRIQ 2023
Бренд: Cadillac Страницы: 337
Jabra FREEWAY Datasheet preview
FREEWAY
Бренд: Jabra Страницы: 2
Jabra BT330 User Manual preview
BT330
Бренд: Jabra Страницы: 38
Yakima K1188 Instructions Manual preview
K1188
Бренд: Yakima Страницы: 12
JEHNERT SOUND DESIGN 65400 Assembly Instruction Manual preview
65400
Бренд: JEHNERT SOUND DESIGN Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды