Skoda Fabia II 2007 Скачать руководство пользователя страница 25

Страница: 25 / 165

Removing
– Remove the storage area on the driver's side ⇒ Body Work;

Rep. gr. 70 .

– Unplug connector from the clutch pedal switch - F36- .
– Turn clutch pedal switch - F36- 90° to the left and remove it

from the support.

Installing and setting
– Remove tappet up to the stop
– Press down the clutch pedal by hand as far as possible.
– Insert clutch pedal switch into the support and turn switch 90°

to the right.

– Insert connector for the clutch pedal switch - F36- .
– Install the storage area on the driver's side ⇒ Body Work; Rep.

gr. 70 .

1.3

Removing and installing, setting cylin‐

drical clutch pedal switch - F36- , (Fabia

II 2007 ►; Roomster 2006 ►)

Note

The clutch pedal switch - F36- may only be installed once to en‐

sure that it has an adequately tight fit in the bracket.

– Remove the storage area on the driver's side ⇒ Body Work;

Rep. gr. 70 .

– Unplug connector -1- from the clutch pedal switch - F36- .
– Turn clutch pedal switch - F36- -2- in the bracket 45° to the left

and remove it from the support.

Note

The clutch pedal remains in the off position in this case (do not

depress).

Installing and setting

– Before installing the clutch pedal switch - F36- pull out tappet

-3- fully.

• Clutch pedal -4- in the off position.
– Guide the clutch pedal switch - F36- through the assembly

opening, press against the clutch pedal and attach by turning

it 45° to the right.

– Insert connector for the clutch pedal switch - F36- .
– Install the storage area on the driver's side ⇒ Body Work; Rep.

gr. 70 .

Fabia II 2007 ➤ , Fabia II 2009 ➤ , Fabia II 2011 ➤ , Rapid 2011 ➤ , R ...

Gearbox 02T - Edition 05.2014

1. Clutch control

Содержание Fabia II 2007






































































































































































Результаты поиска

Содержание Fabia II 2007

Отзывы:

Бренды по названию

Популярные бренды

Skoda Fabia II 2007, Руководство по ремонту

Результаты поиска

Содержание Fabia II 2007

Отзывы:

Бренды по названию

Популярные бренды