Ski-Doo Tundra Skandic Series страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 171

background image

SAFETY INFORMATION

19



Meadows sometimes have low areas where water accumulate
and freezes over in winter. This ice is usually glare ice. Attempting
to turn or brake on this surface could cause your vehicle to spin
out of control. Never brake or attempt speeding or turning on glare
ice. If you do happen to travel over such a condition, reduce speed
by slowly releasing the throttle.



Never “jump” with your snowmobile. This should be left to pro-
fessional stunt men. Don’t show off. Be responsible.



Stay sober.

Safe riders don’t ride under the influence of alcohol or

drugs. Drinking and driving demonstrates a most irresponsible at-
titude not only to others but to yourself. Legislators and the popu-
lation in general do not tolerate it and BRP doesn’t either!



Wildlife compliments your snowmobiling day. Snowmobile tracks
provide firm ground over which animals can travel from area to
area. Do not violate this privilege by chasing or harassing wildlife.
Fatigue and exhaustion can lead to animal’s death. Avoid areas
posted for the protection or feeding of wildlife.



If you happen to be fortunate enough to see an animal, stop your
snowmobile and observe quietly.



Excessive speeding can be fatal. In many cases, you cannot react
or respond quickly enough to the unexpected. Ride at a speed
which is suitable to the trail and weather conditions. If a maximum
speed is posted, observe it.



A poorly maintained snowmobile itself can be a potential hazard.
Excessively worn components could render the vehicle complete-
ly inoperative. Keep the snowmobile in good working condition at
all times. Follow your pre-operation check, weekly, monthly and
annually routine maintenance and lubrication procedures as de-
tailed in this guide. Consult a snowmobile dealer or acquire a shop
manual and proper tools and equipment if other repairs or service
is required.



Raising the rear of your snowmobile while the engine is running
could cause snow, ice or debris to be thrown back at an observer.
Never raise the rear of the vehicle while the engine is running. To
clear or inspect the track, stop the engine, tilt the vehicle on its
side and remove blockage with a piece of wood or branch. Never
allow anyone near a rotating snowmobile track.



Do not stud the track. At speed it may cause the track to tear and
separate from vehicle posing a risk of severe injury or death.



While on safari, do not “gun” the throttle. Snow and ice can be
thrown back into the path of a following snowmobile. In addition,
when “gunning” the throttle, the vehicle digs into and leaves an
irregular snow surface for others.

mmo2005-002b_1.book Page 19 Monday, February 2, 2004 4:07 PM

«
...
19
20
21
22
23
...
»

Содержание Tundra Skandic Series












































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tundra Skandic Series

Бренд: Bad Boy Страницы: 132

Бренд: MANCO Страницы: 5

Бренд: FEATHERLITE TRAILERS Страницы: 78

Cyclone IV Trekking

Бренд: Radical Design Страницы: 2

Бренд: CF MOTO Страницы: 365

Бренд: Honda Страницы: 232

Бренд: Flagro Страницы: 28

Бренд: Axis Страницы: 63

Бренд: Axis Страницы: 74

Бренд: Can-Am Страницы: 147

Бренд: Palms Страницы: 19

Бренд: Taylor-Dunn Страницы: 200

MAVERICK Sport MAX Series

Бренд: Can-Am Страницы: 187

GRIZZLY 350 YFM35FGD

Бренд: Yamaha Страницы: 144

Бренд: Yamaha Страницы: 98

2012 TERRAIN 1500

Бренд: E-Z-GO Страницы: 78

Бренд: E-Z-GO Страницы: 135

Бренд: Access Motor Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды