Sirona XIOS XG Select Скачать руководство пользователя страница 95

Страница: 95 / 120

Sirona Dental Systems GmbH
Gebrauchsanweisung und Installation

5 Operation

64 08 137 D3610
D3610.201.02.09.02 11.2017

5.9

Removing the hygienic protective sleeve from
the sensor

5.9.1

With single-use sensor holder system

Have the sensor holder tab and the sensor holder glued onto the
hygienic protective sleeve. This makes it easier to remove the hygienic
protective sleeve.

NOTICE

The sensor cable is sensitive to mechanical influences.

The cable may become damaged or may wear out prematurely.
➢ Do not pull on the sensor cable when pulling the sensor out of the

hygienic protective sleeve. Slide the sensor further out of the
hygienic protective sleeve with your thumb as described below.

➢ Avoid bending, creasing or rotating the cable or exposing it to

other strains.

Grasp the guide rod in one hand so that you can touch the side of
the sensor facing away from the sensor cable with your thumb.

Carefully push the sensor out of the part of the hygienic protective
sleeve that is glued to the sensor holder tab with your thumb.

Содержание XIOS XG Select

























































































































Результаты поиска

Содержание XIOS XG Select

Отзывы:

Похожие инструкции для XIOS XG Select

Бренды по названию

Популярные бренды

Sirona XIOS XG Select, Инструкция по эксплуатации и установке

Результаты поиска

Содержание XIOS XG Select

Отзывы:

Похожие инструкции для XIOS XG Select

Бренды по названию

Популярные бренды