Simrad GO XSE Series Скачать руководство пользователя страница 34

Страница: 34 / 242

Charts

The Chart panel

North indicator

Vessel

Chart range scale

Grid lines*

Range rings*

* Optional chart items. Optional chart items can be turned on/off
individually from the chart settings dialog.

Chart data

The system can be delivered with preloaded cartography.
For a full selection of supported charts, visit the product web site.

Note:

Chart menu options vary depending on the chart you are

using.

Note:

The system does not automatically switch to preloaded

cartography if the chart card is removed. A low-resolution chart
will be displayed until you re-insert the card or manually switch
back to the preloaded cartography.

Charts

| GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды

Simrad GO XSE Series, Руководство оператора

Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды