manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Maintenance

Preventive maintenance

The unit does not contain any field serviceable components.
Therefore, the operator is required to perform only a very limited
amount of preventative maintenance.

Sun cover

It is recommended that you always fit the sun cover when the unit
is not in use.

Cleaning the display unit

To clean the screen:

•

A micro-fiber or a soft cotton cloth should be used to clean the
screen. Use plenty of water to dissolve and take away salt
remains. Crystallized salt, sand, dirt, etc. can scratch the protective
coating if using a damp cloth. Use a light fresh water spray then
wipe the unit dry with a micro-fiber or a soft cotton cloth. Do not
apply pressure with the cloth.

To clean the housing:

•

Use warm water with a dash of liquid dish soap or detergent.

Avoid using abrasive cleaning products or products containing
solvents (acetone, mineral turpentine, etc.), acid, ammonia, or
alcohol as they can damage the display and plastic housing.
Do not:

•

use a jet or high pressure wash

Checking the connectors

Push the connector plugs into the connector. If the connector plugs
are equipped with a lock or a position key, ensure that it is in the
correct position.

Touchscreen calibration

Use the system setting option to calibrate the touchscreen.

28 

220

Maintenance

 | GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

DARAY BH200 Operating & Installation Manual preview
BH200
Бренд: DARAY Страницы: 24
Jafar 7110 Operation And Maintenance Manual preview
7110
Бренд: Jafar Страницы: 9
C.M.O FL Series Instruction And Maintenance Manual preview
FL Series
Бренд: C.M.O Страницы: 10
Cadex C8000 User Manual preview
C8000
Бренд: Cadex Страницы: 300
Campbell SkyVUE 8M Quick Deploy Manual preview
SkyVUE 8M
Бренд: Campbell Страницы: 2
Eaton Crouse-hinds series Technical Manual preview
Crouse-hinds series
Бренд: Eaton Страницы: 32
Gary Machinery 3354 Instruction Manual preview
3354
Бренд: Gary Machinery Страницы: 14
Hantek Tablet1000 Series User Manual preview
Tablet1000 Series
Бренд: Hantek Страницы: 98
Launch X431 V Quick Start Manual preview
X431 V
Бренд: Launch Страницы: 3
Launch EasyDiag User Manual preview
EasyDiag
Бренд: Launch Страницы: 43
Launch X-431 Diagun Faq preview
X-431 Diagun
Бренд: Launch Страницы: 8
Launch X-431 PAD III User Manual preview
X-431 PAD III
Бренд: Launch Страницы: 67
Launch X-431 PADII User Manual preview
X-431 PADII
Бренд: Launch Страницы: 55
LAUNCH TECH Creader 629 Quick Start Manual preview
Creader 629
Бренд: LAUNCH TECH Страницы: 14
Launch X-431 PROS V4.0 User Manual preview
X-431 PROS V4.0
Бренд: Launch Страницы: 80
Ultrawave Neon Series Operator'S Manual preview
Neon Series
Бренд: Ultrawave Страницы: 30
Ultrasound Technologies PD1 series Operating Instructions Manual preview
PD1 series
Бренд: Ultrasound Technologies Страницы: 12
Varytec LED Street Bar 16x3W RGB IP65 User Manual preview
LED Street Bar 16x3W RGB IP65
Бренд: Varytec Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды