manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Placing EBL/VRM markers by using the cursor

1.

Position the cursor on the radar image

2.

Activate the menu

3.

Select one of the EBL/VRM markers

- The EBL line and the VRM circle are positioned according to

the cursor position.

Offsetting an EBL/VRM marker

1.

Ensure that the cursor is not active

2.

Activate the menu, select 

EBL/VRM

, then select the marker you

wish to offset

3.

Select the set offset option

4.

Position the cursor on the radar panel to set the offset position

5.

Select the save option to save your settings.

You can reset the EBL/VRM center to vessel position from the menu.

Recording radar data

You can record radar data and save the file internally in the unit, or
save it onto a storage device connected to the unit.
A recorded radar file can be used for documenting an event or an
operational error. A logged radar file can also be used by the
simulator.

Ú

Note: 

The record menu option is available if recording is turned

on in the Advanced system settings.

132

Radar

 | GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Federal Signal Corporation VECTOR Installation And Maintenance Instructions preview
VECTOR
Бренд: Federal Signal Corporation Страницы: 2
Harman Kardon EQ8 Owner'S Manual preview
EQ8
Бренд: Harman Kardon Страницы: 7
Gardol GLVE 1400-34 Original Operating Instructions preview
GLVE 1400-34
Бренд: Gardol Страницы: 260
York Fitness 60091 Owner'S Manual preview
60091
Бренд: York Fitness Страницы: 20
VBM POCKET Instructions For Use Manual preview
POCKET
Бренд: VBM Страницы: 36
W&H Med Lara Instructions For Use Manual preview
Lara
Бренд: W&H Med Страницы: 122
K-9 Lights Bulldog User Manual preview
Bulldog
Бренд: K-9 Lights Страницы: 12
K'Nex Education 79319 Manual preview
79319
Бренд: K'Nex Education Страницы: 2
laerdal SimMan 3G Trauma Quick Setup Manual preview
SimMan 3G Trauma
Бренд: laerdal Страницы: 16
laerdal SimMan 3G Maintenance Manual preview
SimMan 3G
Бренд: laerdal Страницы: 16
laerdal SimMan Important Product Information preview
SimMan
Бренд: laerdal Страницы: 60
laerdal Nursing Baby Manual preview
Nursing Baby
Бренд: laerdal Страницы: 4
laerdal Resusci Anne Simulator Important Product Information preview
Resusci Anne Simulator
Бренд: laerdal Страницы: 8
laerdal Nursing Baby VitalSim Manual preview
Nursing Baby VitalSim
Бренд: laerdal Страницы: 15
Safavieh TBL4102 Quick Start Manual preview
TBL4102
Бренд: Safavieh Страницы: 2
Vendlet STANDARD Quick Manual preview
STANDARD
Бренд: Vendlet Страницы: 2
XanLite TO1500L User Manual preview
TO1500L
Бренд: XanLite Страницы: 4
Olympus EVIS EXERA III Instructions Manual preview
EVIS EXERA III
Бренд: Olympus Страницы: 130

Бренды по названию

Популярные бренды

Загрузить еще бренды