Simrad GO XSE Series Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 242

background image

The autopilot will engage in the selected mode, and the autopilot
controller will change to show active mode options.
To disengage the autopilot:

•

Select the standby button

When the autopilot is in standby, the boat must be steered
manually.

Autopilot indication

The status bar shows autopilot information as long as an autopilot
computer is connected.

Autopilot modes

The autopilot has several steering modes. The number of modes
and features within the mode depend on the autopilot computer,
the boat type and available inputs.

Non-Follow Up mode (NFU)

In this mode the port and starboard buttons are used to control the
rudder.
Activate this mode by selecting the port or starboard button when
the autopilot is in standby.

To change the rudder position

•

Select a port or starboard button.

The rudder moves as long as the button is pressed.

100

Outboard autopilot

| GO XSE/XSR Operator Manual

«
...
98
99
100
101
102
...
»

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

SafetuNet Alert

Бренд: Masimo Страницы: 2

Бренд: Modulate Страницы: 2

Бренд: Kawai Страницы: 10

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: Garmin Страницы: 2

Бренд: Garelick Страницы: 4

Бренд: Patty-O-Matic Страницы: 28

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: UniPix Страницы: 24

Бренд: MAKSIWA Страницы: 155

Бренд: Yacht Devices Страницы: 68

Бренд: Wacker Neuson Страницы: 42

Бренд: KERR Страницы: 32

Бренд: TEUCER Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды