Simrad ES38-10 - REV B Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

Simrad ES38-10 - REV B Скачать руководство пользователя страница 32

Simrad ES38-10

Cable glands for small hulls

This cable glands made of plastic is designed for those smaller
vessels that do not need to be classified.

(CD17008C)

A

A

J

B

C

D

G

E

F

H

I

(A) = Packing nut (bronze). Ensure that you do not to damage
the transducer cable by tightening the packing nut too hard!

(B) = Rubber gasket

(C) = Plastic disk

(D) = Rubber gasket

(E) = Stuffing tube

(F) = Backing nut (bronze)

(G) = Backing washer (plastic)

(H) = O-ring 42.5 x 3.0 N

(I) = O-ring 39.5 x 3.0 N

(J) = Cable to the echo sounder (or a junction box)

Stuffing tube hole diameter: 36 mm ±1.5 mm.

Apply ample amount of sealant between the backing washer (H)
and the hull plate.

The cable gland kit contains all the listed parts, except the sealant.

Note

The two O-rings must be clean, in good condition and free of cuts
or other defects which could affect their watertight integrity.

30

305176/A

«
...
30
31
32
33
34
...
»

Содержание ES38-10 - REV B





















































Отзывы:

Нет отзывов