background image

1

5101610

Rev C

Dealer Setup
& Adjustment Instructions

Simplicity ZT4000 Series Zero-Turn Riding Mower

TABLE OF CONTENTS:

SETUP PROCEDURES
Quick Setup List..................................................2
Uncrating ..........................................................3
Connect the Battery..............................................3
Tractor Assembly ................................................4

Ground Speed Control Lever Assembly ...........................4
Seat Assembly ..................................................................5

Roll Bar Assembly ...............................................6
Check Fluid levels ...............................................7

Check Engine Oil Level .....................................................7
Check Hydraulic Oil Level .................................................7

Check Tire Pressure .............................................7
Mower Assembly.................................................8

Check Torque - Mower Blades .........................................8

Deck Lift Rod Timing & Leveling Adjustment ...............8
Check Deck Drive Belt ........................................ 10
Lubrication ...................................................... 12
Adding Fuel ..................................................... 13
Starting The Engine ........................................... 13
Perform Safety Checks ........................................ 13

Functional Tests .............................................................13
Safety Interlock System .................................................14

ADJUSTMENT PROCEDURES
Neutral Adjustment ............................................ 14
Return-To-Neutral Adjustment ............................... 15
Parking Brake Adjustment .................................... 15
Suspension Adjustment ....................................... 16

This Dealer Setup Instruction covers the following products:

ZT4000 Series Zero-Turn Riding Mower

Model No.:

Description:

5900707

ZT4000B2444

44” Mower Deck

5900765

ZT4000B2648

48” Mower Deck

5900960

ZT4000B2748

48” Mower Deck

Attention Setup Personnel:

The safety warnings provided in this 
guide and in the operator’s manual 
included with the unit contain important 
information that must be obeyed when 

assembling, setting-up, operating, servicing, 
transporting, or storing the unit.

These warnings are highlighted by the safety alert 
triangle symbol shown above, which signifies that 
an important safety message is being provided.   

You must read, understand, and follow these 
warnings and instructions, and use safe shop 
and work practices at all times while working on 
or around this unit and all other outdoor power 
equipment.

Sections and items denoted by the Setup 
symbol provide the information necessary to fully 
assemble, test, and prepare the units described 
above for delivery to your customers.

A Quick Setup List is provided on page 2 of this booklet 
to help you identify and check that the items have been 
performed.

Additional information concerning functional 
tests, general adjustment procedures, and the 
location of normal lubrication points are included 
in these instructions.

Although all required lubrication and normal adjustments on 
factory-assembled components are done at the factory, this 
additional information is provided to assist you in ensuring 
that each unit is delivered to the customer in proper working 
order.

Not 

for  

Reproduction

Содержание 5900707

















Отзывы: