background image

Cautions, Warnings, and Regulatory Information

READ AND SAVE THESE INSTRUCTIONS

 Follow the instructions in this installation manual. These instructions must be followed to avoid damage to

this product and associated equipment. Product operation and reliability depend upon proper installation.

DO NOT INSTALL ANY SIMPLEX™ PRODUCT THAT APPEARS DAMAGED

 Upon unpacking your Simplex product, inspect the contents

of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex

product supplier.

ELECTRICAL HAZARD

 Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be

performed by a representative or an authorized agent of your local Simplex product supplier.

STATIC HAZARD

 Static electricity can damage components. Handle as follows:

•  Ground yourself before opening or installing components.
•  Prior to installation, keep components wrapped in anti-static material at all times.

EYE SAFETY HAZARD

 Under certain fibreoptic application conditions, the optical output of this device may exceed eye safety limits. Do

not use magnification (such as a microscope or other focusing equipment) when viewing the output of this device.

FCC RULES AND REGULATIONS – PART 15.

 This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES

 To ensure proper system operation, this product must be tested in accordance with

NFPA72® after any programming operation or change in site-specific software. Reacceptance testing is required after any change, addition or deletion

of system components, or after any modification, repair or adjustment to system hardware or wiring.
All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that

other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50

devices, must also be tested and proper system operation verified.
NFPA 72® is a registered trademark of the National Fire Protection Association.

Introduction to Amplifiers

Introduction

This publication describes the installation procedure for the 4100U and 4100ES Fire Alarm Control Units (FACU) family of digital and analog amplifiers.

Important: 

Verify FACU System Programmer, Executive, and Slave Software compatibility when installing, or replacing system components. Refer to

the Technical Support Information and Downloads website for compatibility information.

Overview

The digital and analog audio amplifiers provide analog audio power to the system speaker circuits. Digital amplifiers decode digitally encoded input

signals and analog amplifiers receive analog input signals. A speaker circuit consists of one or more speakers that are driven by the same physical

wiring. All of the 100 W amplifiers described in this document are single channel amplifiers; that is, each speaker circuit is driven by the same audio

signal. See the next section for a list of all 100 W amplifiers.

579-174   Rev. Q

Digital/Analog Amplifiers Installation Instructions

*0579174Q*

Содержание 4100-1314















Отзывы: