SimCom SIM5215 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 72

SimCom SIM5215 Скачать руководство пользователя страница 50

Smart Machine Smart Decision

Table 31: Timing parameters

Parameter

Description

Min

Typ

Max

Unit

T(sync)

PCM_SYNC cycle time

–

125

–

μ

s

T(synch)

PCM_SYNC high time

400

500

–

ns

T(syncl)

PCM_SYNC low time

–

124.5 –

μ

s

T(clk)

PCM_CLK cycle time

–

488

–

ns

T(clkh)

PCM_CLK high time

–

244

–

ns

T(clkl)

PCM_CLK low time

–

244

–

ns

T(susync)

PCM_SYNC setup time high before falling edge of
PCM_CLK

60

–

–

ns

T(hsync)

PCM_SYNC hold time after falling edge of
PCM_CLK

60

–

–

ns

T(sudin)

PCM_DIN setup time before falling edge of
PCM_CLK

50

–

–

ns

T(hdin)

PCM_DIN hold time after falling edge of
PCM_CLK

10

–

–

ns

T(pdout)

Delay from PCM_CLK rising to PCM_DOUT valid

–

–

350

ns

T(zdout)

Delay from PCM_CLK falling to PCM_DOUT
HIGH-Z

–

160

–

ns

Note: SIM5215&SIM5216 can transmit PCM data by USB except for PCM interface. Please refer to document [22] for

more information of PCM Application Note.

3.12

Multi-functional interface

SIM5215&SIM5216 merges functions for various applications. It can enrich users’ design and lower the
cost of users’ hardware.

3.12.1

Reset Function

SIM5215&SIM5216 also have a RESET pin (PIN29) to reset the module. This function is used as an
emergency reset only when AT command “AT+CPOF” and the POWER_ON pin has no effect. User can
pull the RESET pin to ground, then the module will reset.

This pin is already pulled up in module, so the external pull-up resistor is not necessary. A 100nF capacitor
close to the RESET pin is strongly recommended. A reference circuit is recommended in the following
figure.

SIM5215&SIM5216_Hardware Design_V2.02

2012-08-31

50

«
...
48
49
50
51
52
...
»

Содержание SIM5215









































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды