manualshive.com logo in svg

Silicon Laboratories EFR32BG13 Blue Gecko, Руководство пользователя, Страница: 1 / 33

Поделиться
Скачать
Silicon Laboratories EFR32BG13 Blue Gecko Скачать руководство пользователя страница 1

UG279: EFR32BG13 Blue Gecko Bluetooth
Starter Kit User's Guide

A Silicon Labs Wireless Starter Kit for the EFR32BG13 Blue
Gecko is an excellent starting point to get familiar with the device,
and it provides all necessary tools for developing a Silicon Labs
wireless application.

The Wireless Starter Kit Mainboard contains sensors and peripherals enabling easy
demonstration of some of the EFR32™'s many capabilities. An on-board J-Link debug-
ger allows debugging of the attached radio board as well as providing a debug connec-
tion for external hardware.

A plug-in Radio Board contains the reference design for the EFR32 itself, including the
RF section and device-specific hardware.

WSTK MAINBOARD FEATURES

• Ethernet and USB connectivity
• Advanced Energy Monitor
• Virtual COM Port
• Packet Trace Interface support
• SEGGER J-Link on-board debugger
• Supports debugging the attached radio

board or an external device

• Silicon Labs' Si7021 Relative Humidity

and Temperature sensor

• Ultra low power 128x128 pixel Memory

LCD

• User LEDs / Pushbuttons
• 20-pin 2.54 mm header for expansion

boards

• Breakout pads for direct access to all radio

I/O pins

• Power sources include USB, CR2032 coin

cell and AA batteries.

BRD4104A RADIO BOARD FEATURES

• EFR32BG13 Blue Gecko Wireless SoC

with 512 kB Flash and 64 kB RAM
(EFR32BG13P632F512GM48).

• Inverted-F PCB antenna (2.4 GHz band)
• 8 Mbit low-power serial flash for over-the-

air upgrades.

SOFTWARE SUPPORT

• Simplicity Studio™
• Energy Profiler
• Network Analyzer

silabs.com

 | Smart. Connected. Energy-friendly.

Rev. 1.00

Содержание EFR32BG13 Blue Gecko


































Отзывы:

Нет отзывов