manualshive.com logo in svg

Silicon Graphics InfiniteStorage C1104-GP6, Руководство пользователя системы

Поделиться
Скачать
Silicon Graphics InfiniteStorage C1104-GP6 Скачать руководство пользователя страница 39

Drive Carrier LEDs

007-6465-001

27

•

A slow red blink indicates a power failure - check the function of the system power supplies 
at the back of the unit.

•

A fast red blink indicates a fan failure - check for a failed cooling fan and replace as soon as 
possible.

Figure 3-10

Overheat/Fan Fail/Info LED Example 

Drive Carrier LEDs

The system hard disk drives each have two LEDs, that function as listed in the following two 
paragraphs:

•

Green: When illuminated, the green LED on the drive carrier indicates drive activity. A 
connection to the drive backplane enables this LED to blink on and off when that particular 
drive is being accessed. Please refer to Chapter 6 for instructions on replacing failed drives. 

•

Red: When this LED is flashing it indicates that a RAID drive is rebuilding. A solidly lit red 
LED indicates a drive failure. If the drives fails, you should be notified by your system 
management software. Refer to Chapter 6 for instructions on replacing failed drives. 

Содержание InfiniteStorage C1104-GP6













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды