Silicon Graphics InfiniteStorage C1104-GP6 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 76

background image

Server Chassis Features

007-6465-001

5

Server Chassis Features

The following subsections provide a general outline of the main features of the ISS C1104-GP6
chassis.

System Power

The SGI ISS C1104-GP6 1U chassis features a redundant power supply composed of two separate
power modules. This power redundancy feature allows you to replace a failed power supply
without shutting down the system. Note that each power supply provides up to 500 Watts of power
to the system.

Serial ATA Subsystems

The server chassis supports up to four 3.5-in SATA drives. Chassis drives are SATA 3.0
6-Gb/second slots. RAID 1 drives are hot-swappable units and are connected to a backplane that
provides power and control. Note that the operating system you have installed must support RAID
to enable the hot-swap capability of RAID drives. Certain RAID levels may require use of
optional hardware or software to support RAIDed hard disk drives in the server.

Front Control Panel

The control panel on the ISS C1104-GP6 provides you with chassis monitoring and control. LEDs
that indicate system power, HDD activity, network activity and a chassis overheat/fan-fail/ UID
LED. A main power button and a system reset button are also included.

Serverboard and PCIe Subsystem

The ISS C1104-GP6 chassis is an ATX form factor chassis designed to be used in a 1U rackmount
configuration. The serverboard’s I/O backplane supports two standard size (full-height x16) PCIe
cards and one half-height (x8) PCIe card which can offer optional computing solutions. A 15-pin
VGA port, a serial (COM) port, two USB 3.0 and two USB 2.0 ports, two Gigabit LAN ports and
a dedicated RJ-45 IPMI LAN port are also supported.

«
...
15
16
17
18
19
...
»

Содержание InfiniteStorage C1104-GP6













































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage C1104-GP6

Бренд: IBM Страницы: 214

SUPERSERVER 5018D-MHR7N4P

Бренд: Supermicro Страницы: 126

Бренд: Sercomm Страницы: 75

FusionServer CH242 V5

Бренд: xFusion Digital Technologies Страницы: 61

UltraNEXUS-HD Flex

Бренд: Leightronix Страницы: 5

Netfinity 1000-8477 21Y

Бренд: IBM Страницы: 268

Бренд: Jatheon Страницы: 52

DLAP-201 Series

Бренд: ADLINK Technology Страницы: 39

Бренд: IOGear Страницы: 48

Sun Fire Netra 1280

Бренд: Sun Microsystems Страницы: 10

S7000FC4UR - Server System - 0 MB RAM

Бренд: Intel Страницы: 13

Бренд: Advantech Страницы: 3

eserver xSeries 350

Бренд: IBM Страницы: 174

Бренд: Planet Страницы: 87

G4-Apex-ENTERPRISE-HW

Бренд: Viavi Страницы: 8

Бренд: Tibbo Страницы: 12

Бренд: Xantech Страницы: 52

DSTni-XPress DR

Бренд: Lantronix Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды