manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание


Поделиться
Скачать
background image

158

How Volume Copy Works 

A mirror repository volume

A failed volume

A missing volume

A volume currently in a modification operation

A volume that is holding a Small Computer System Interface-2 (SCSI-2) 

reservation or a persistent reservation

A volume that is a source volume or a target volume in another volume copy that 

has a status of In Progress, Pending, or Failed

Target Volume

A target volume contains a copy of the data from the source volume. When a volume 

copy is started, data from the source volume is copied in its entirety to the target 

volume. 

ATTENTION  Possible loss of data access

 – A volume copy overwrites data on the 

target volume. Before you start a new operation, make sure that you no longer need the 

old data, or you have backed up the old data on the target volume.

While the volume copy has a status of In Progress, Pending, or Failed, the controllers 

reject read and write requests to the target volume. After the volume copy operation is 

finished, the target volume automatically becomes read only to the hosts, and write 

requests to the target volume are rejected. You can change the Read-Only attribute 

after the volume copy has completed or has been stopped. (For more information 

about the Read-Only attribute, see “

Viewing Volume Copy Properties

.”

The following volumes are valid target volumes:

A standard volume

The base volume of a disabled snapshot (legacy) volume or failed snapshot 

(legacy) volume

A primary volume that is participating in a remote-mirror pair

The following volumes are not valid target volumes:

The base volume of an active snapshot (legacy) volume

A snapshot (legacy) volume

A mirror repository volume

A snapshot (legacy) repository volume

A secondary volume in a remote-mirror pair

A failed volume

A missing volume

A volume with a status of Degraded

A volume that is currently in a modification operation

Содержание InfiniteStorage 4000 Series





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage 4000 Series

D-Link DSL-2640BT Installation Manual preview
DSL-2640BT
Бренд: D-Link Страницы: 12
Razberi V8 Core Manual And Getting Started Manual preview
V8
Бренд: Razberi Страницы: 113
DANE-ELEC SO MOBILE OTB HELLO KITTY Quick Start Manual preview
SO MOBILE OTB HELLO KITTY
Бренд: DANE-ELEC Страницы: 16
Far south networks Com.X1 PBX Getting Started preview
Com.X1 PBX
Бренд: Far south networks Страницы: 4
G-Technology G-RAID Studio User Manual preview
G-RAID Studio
Бренд: G-Technology Страницы: 51
X-Micro WLAN 11g User Manual preview
WLAN 11g
Бренд: X-Micro Страницы: 74
Zhone 6211 Product Manual preview
6211
Бренд: Zhone Страницы: 7
LaCie 301160U - 1TB Ethernet Disk RAID Network Attached... Quick Install Manual preview
301160U - 1TB Ethernet Disk RAID Network Attached...
Бренд: LaCie Страницы: 5
LaCie 301382U Specifications preview
301382U
Бренд: LaCie Страницы: 6
Point Six Link Manager 4010-43 Manual preview
Link Manager 4010-43
Бренд: Point Six Страницы: 131
Secure Data SecureUSB BT Quick Start Manual preview
SecureUSB BT
Бренд: Secure Data Страницы: 2
Hornington AirStation WHR-G300N Settings preview
AirStation WHR-G300N
Бренд: Hornington Страницы: 6
LaCie 2big DOCK User Manual preview
2big DOCK
Бренд: LaCie Страницы: 48
Seagate ST31230N/ND Installation Manual preview
ST31230N/ND
Бренд: Seagate Страницы: 36
Supermicro SUPERSERVER 6034H-X8R User Manual preview
SUPERSERVER 6034H-X8R
Бренд: Supermicro Страницы: 128
Alcatel Speed Touch 591s Technical User'S Manual preview
Speed Touch 591s
Бренд: Alcatel Страницы: 184
Asante IntraCore 6524 User Manual preview
IntraCore 6524
Бренд: Asante Страницы: 150
NAIM UNITISERVE - Quick Start Manual preview
UNITISERVE -
Бренд: NAIM Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды