manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание


Поделиться
Скачать
background image

140

Deleting an Asynchronous Mirror Group 

remove volume ["Jan_04_Account"] 

asyncMirrorGroup="amg_001" 

deleteRepositoryMembers=TRUE;

You must run this command on the local storage array to remove the primary volume.
If the volume is not successfully removed from both sides of the asynchronous mirror 

group, the mirror volume that was not removed becomes an orphan. Orphans are 

detected when communications between the controller on the local storage array and 

the corresponding controller on the remote storage array is restored. At that time the 

two sides of the mirror configuration reconcile mirror parameters. Some 

synchronization operations function normally when a asynchronous mirror group 

contains orphaned members, but some configuration operations, such as role change, 

cannot be performed when the asynchronous mirror group contains orphaned 

members. To avoid this situation, remove the incomplete mirror volumes by running 

this command:

remove asyncMirrorGroup ["

asyncMirrorGroupName

"] 

incompleteMirror volume="

volumeName

"

Deleting an 
Asynchronous 
Mirror Group

If you need to remove an asynchronous mirror group for any reason, you can remove 

it using this command:

delete asyncMirrorGroup

Before you can delete an asynchronous mirror group you must remove the primary 

volume, the secondary volume, and the repository volume from the asynchronous 

mirror group. The asynchronous mirror group must be completely empty before you 

can delete it. You can remove these volumes using this command:

remove volume asyncMirrorGroup

Removing these volumes from the asynchronous mirror group does not delete the 

volumes. The data is not lost.
Deleting the asynchronous mirror group first removes the remote asynchronous 

mirror group then removes the local asynchronous mirror group. You can run the 

delete asyncMirrorGroup

 command from either the primary asynchronous 

mirror group or secondary asynchronous mirror group.

Содержание InfiniteStorage 4000 Series





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage 4000 Series

IBM 8275-416 Quick Reference Card preview
8275-416
Бренд: IBM Страницы: 8
G-Technology G-DRIVE mini Installation Manual preview
G-DRIVE mini
Бренд: G-Technology Страницы: 13
Conceptronic C150BRS4 Multi Language Quick Manual preview
C150BRS4
Бренд: Conceptronic Страницы: 2
Sun Microsystems Sun Fire V880z Installation And User Manual preview
Sun Fire V880z
Бренд: Sun Microsystems Страницы: 128
NETGEAR RAXE500 User Manual preview
RAXE500
Бренд: NETGEAR Страницы: 169
Sans Digital MOBILERAID MR5S1 Quick Installation Manual preview
MOBILERAID MR5S1
Бренд: Sans Digital Страницы: 1
SafeNet Luna SA Configuration Manual preview
Luna SA
Бренд: SafeNet Страницы: 109
IBM totalstorage 200 Service Manual preview
totalstorage 200
Бренд: IBM Страницы: 180
Patton electronics SMARTNODE 4950 Quick Start Manual preview
SMARTNODE 4950
Бренд: Patton electronics Страницы: 12
AMX NXA-ENET8POE Installation Manual preview
NXA-ENET8POE
Бренд: AMX Страницы: 2
Planet IGS-5225-20T4C2X Quick Installation Manual preview
IGS-5225-20T4C2X
Бренд: Planet Страницы: 16
ZyXEL Communications Prestige 2864I Getting Started preview
Prestige 2864I
Бренд: ZyXEL Communications Страницы: 8
Calix GS2020E GigaSPIRE BLAST Quick Start Manual preview
GS2020E GigaSPIRE BLAST
Бренд: Calix Страницы: 15
Swissbit iCCT User Manual preview
iCCT
Бренд: Swissbit Страницы: 11
3Com Router 3033 Configuration Manual preview
Router 3033
Бренд: 3Com Страницы: 63
Weidmüller IE-SW-AL18M-16TX-2GC Hardware Installation Manual preview
IE-SW-AL18M-16TX-2GC
Бренд: Weidmüller Страницы: 2
H3C LS-5100-16P-SI-OVS-H3 Configuration preview
LS-5100-16P-SI-OVS-H3
Бренд: H3C Страницы: 313
IBM Travelstar 10E Installation And Operation Manual preview
Travelstar 10E
Бренд: IBM Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды