Silicon Graphics InfiniteStorage 4000 Series Скачать руководство пользователя страница 148

Страница: 148 / 276

136

Manually Resynchronizing Volumes in an Asynchronous Mirror Group

Manually
Resynchronizing
Volumes in an
Asynchronous
Mirror Group

Manually resynchronizing the volumes in an asynchronous mirror group immediately

resynchronizes all of the mirror relationships within the asynchronous mirror group.

You cannot perform this operation if one of these conditions exists:



The asynchronous mirror group has failed because any dependent component of

the mirror configuration is in a Failed state.



The asynchronous mirror group is in a Suspended state.

The manual resynchronization request must be issued to the primary asynchronous

mirror group.
You can run a manual resynchronization on an asynchronous mirror group that is

configured with a periodic synchronization interval. A manual resynchronization does

not affect the periodic resynchronization schedule. If you manually resynchronize the

asynchronous mirror group when it is performing an initial synchronization, the

manual resynchronization command is rejected.
If you run a manual resynchronization when an asynchronous mirror group is in the

midst of a periodic synchronization operation, the current process is stopped and the

point in time synchronization points on the primary are discarded. The delta log

tracking new host writes and the delta log being used for the synchronization process

are merged. New point in time synchronization points are created and a new

resynchronization is started.
To manually run a resynchronization, run this command:

start asyncMirrorGroup synchronize

Changing
Asynchronous
Mirroring Roles

You can change the mirroring roles of an asynchronous mirror group, promoting the

secondary storage array to the primary storage array. Each storage array changes

roles. First the original primary becomes the secondary, and then the original

secondary becomes the primary. As soon as the role change completes, all

asynchronous mirror group member volumes on the new-primary storage array

become fully accessible for host I/O operations. Follow these guidelines when

changing roles:



You can run the command to change roles from either primary storage array or

secondary storage array.



All of the mirror pairs of the asynchronous mirror group must have a valid

recovery point before performing a role reversal.



The asynchronous mirror group must be in a non-failed state and must not

already be in role changing operation.



You cannot change roles if the asynchronous mirror group contains incomplete or

orphaned member volumes.

When the communication between the asynchronous mirroring storage arrays is

operating normally, role reversal is coordinated between the local and remote storage

arrays. During role reversal these two events occur:

Содержание InfiniteStorage 4000 Series




















































































































































































































































































Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание

Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды