Silicon Graphics InfiniteStorage 4000 Series Скачать руководство пользователя страница 136

Страница: 136 / 276

124

How Asynchronous Mirroring Works



Data on the secondary volume must support a site-level failover for disaster

recovery. For this reason, the data on the secondary volume is protected during

the synchronization process so that writes to the secondary volume do not render

the volume data unusable. Additionally, many applications require the use of

more than one volume, each of which must be mirrored in order to support a

site-level failover. In these cases, the set of volumes must be mirrored as a set,

and the synchronization process must coordinate the data movement and

synchronization intervals to create a consistent, usable data set on the secondary

storage array.

Configurating for
Asynchronous
Mirroring

Asynchronous mirroring operations are performed between controllers that have same

IDs on the primary and secondary storage arrays; that is, controller A on the primary

storage array interacts only with controller A on the secondary storage array and

controller B on the primary storage array interacts only with controller B on the

secondary storage array. Asynchronous mirroring operations are not attempted

between controllers that have different IDs. The network environment does not need

to provide connectivity between the controllers that have different IDs; however, it is

likely to be more cost effective to use a fabric/switch configuration that does provide

such connectivity, even though the firmware does not require it.
For Fibre Channel topology the Asynchronous Mirroring premium feature requires

that one host-side Fibre Channel port of each controller be dedicated to mirroring

operations. An additional requirement for connectivity is that the dedicated

asynchronous mirroring ports must be attached to a Fibre Channel Fabric. The

dedicated port is activated by the storage system administrator. Activating the

dedicated port is a different operation than enabling the premium feature. After you

activate the dedicated port you must enable the Asynchronous Mirroring premium

feature. Enabling the Asynchronous Mirroring premium feature performs these

actions:



Activates the storage array for Fibre Channel mirroring



Enables the controller firmware to support your creation of mirror groups and

mirror pairs

When mirror groups or mirror pairs exist, you cannot deactivate the Asynchronous

Mirroring premium feature.
An iSCSI topology does not require a dedicated port as with Fibre Channel. The

activation step is not required when setting up asynchronous mirroring over iSCSI.

The controller firmware maintains a list of remote storage arrays that the iSCSI

initiator attempts to establish sessions using all portals of the portal group. The first

portal that successfully establishes an iSCSI connection is used for all subsequent

communication with that remote storage array. If communication fails, a new session

is attempted using all portals in the portal group. iSCSI ports are configured at the

system level on a port-by-port basis. For configuration messaging and data transfer,

the communication between the controller uses these global settings:

Содержание InfiniteStorage 4000 Series




















































































































































































































































































Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание

Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды