Silex technology MNS-300EM Скачать руководство пользователя страница 101

Страница: 101 / 134

10. TCP/IP Commands

Enables/Disables the Raw TCP (9100) protocol.

SET IP TCP [ENable | DISable]

ENable

Enables the Raw TCP (9100) protocol.

DISable

Disables the Raw TCP (9100) protocol.

The factory default value is

ENable

10-7. SET IP TCP

Enables/Disables the LPD protocol.

SET IP LPD [ENable | DISable]

ENable

Enables the LPD protocol.

DISable

Disables the LPD protocol.

The factory default value is

ENable

10-8. SET IP LPD

Enables/Disables the Silex Technology's proprietary protocol.

SET IP SX_INTERN [ ENable | DISable]

ENable

Enables the Silex Technology's proprietary protocol.

DISable

Disables the Silex Technology's proprietary protocol.

The factory default value is

ENable

10-9. SET IP SX_INTERN

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды