background image

TM

Silent

Alert

Quick start guide UM3A-2212-EU-PSU

Smoke / Carbon Monoxide Monitor with inline PSU

 

CCM3A-2216-EU-PIR-MKX

MOVEMENT MONITOR 11/12/13

USE MAINS POWER SUPPLY

PS3A-2207-UK ONLY

SILENT ALERT SA3000 SYSTEM

WWW.SILENT-ALERT.CO.UK CLOFIELD LTD. UK

TEL 01246 260045

MOVE KEY

 DOWN 

TO SWITCH 

ON

 

Any questions? Call us on 01246 450789

 

1

2 3 4 5

 

B

5

4

3

2

1

ON /OFF

O

N

1

2

3

 

1.

A

 

4

A

 

4

5

4

5

 

SW3935

 

I/P: 

AC 100

-240V

O/P: DC 9V 1.3A

Power supply 

Connect the power supply to 
a 13 Amp fused spur. 
 
 

 
 
 

 

WARNING

This product should only be installed by 

a suitably qualified person.

  Clofield take no responsibility for damage 

caused by incorrect fitting.

 

WARNING! Your device and its accessories are not toys. They may contain small parts. Keep them out of the reach of small children.

Test button

1
2
3
4
5
6
7
8

9

10
11
12
13
14
15
16

UM3A-2212-EU-PSU

USE MAINS POWER SUPPLY

PS3A-2207-UK ONLY

SILENT ALERT SA3000 SYSTEM

WWW.SILENT-ALERT.CO.UK CLOFIELD LTD. UK

TEL 01246 260045

 

  1 = System Code 1

  2= System Code 2

  3 = System Code 3 

  4 = System Code 4

  5 = 

Audio

 Monitor

ing

  6 = Zone Multipl

ier (7

-12)

  7 = Short 

Audio

 Delay

  8 = Medium 

Audi

o Delay

  7 & 8 = Long 

Audio

 Delay

  9 = PIR Delay 5 Mins

10 = PIR Delay 10

 Mins

9 & 10 = PIR Dela

y 15 mins

11 = Zone 6

12 = Zone 5

13 = Zone 4

14 = Zone 3

15 = Zone 2

16 = Zone 1

MOVE KEY

 DOWN 

TO SWITCH 

ON

Alkaline 

NOTE: if this is done in 
reverse order a low battery 
signal will be sent out and 
the test/send button will 
shine orange instead of 
green for up to 9 hours.

Power the unit.

WARNING. DO NOT APPLY MAINS VOLTAGE TO THE UNIT AS THIS WILL CAUSE IRREVOCABLE DAMAGE, 

CAUSE INJURY AND CREATE A FIRE HAZARD

.

 

Volt-free relay / short circuit activation

The UM3A-2212-EU-PSU should ideally be connected to interconnected smoke 
alarms via a normally open volt-free relay using terminals 1 & 3 as shown.
 
 

Low voltage activation

Link the Monitor via terminals 1 & 2 (middle and bottom terminals). Link the 
LOW VOLTAGE Interlink Terminal within the device to terminal 2 (middle 
terminal) on the monitor and the Neutral terminal within the alarm to Terminal 1 
(bottom terminal) on the Monitor.
 
Activate the alarm system, this will cause the monitor to transmit a radio signal 
and the green light on the front of the unit will go out momentarily. 
 
Test the unit in position then fasten to the wall with the screw kit provided.

2. Interconnect smoke / heat / Carbon Monoxide connection

Switch the mains off, 
remove the battery and 
reset the unit using the 
procedure in step 1.

This monitor will send a 
fire signal by default.

 

 
It can be configured to transmit a 
Carbon Monoxide signal (see reverse).

Connect a PP3 battery to the 
unit then power the unit by 
switching the mains on.

 

The test button will light 
green, this is normal.

 

PLEASE NOTE

.

THIS PRODUCT 

DOES NOT

 COMPLY WITH BS5839-1 2002. HOWEVER, THE FIRE SAFE INTERFACE PANEL, ALSO 

AVAILABLE FROM CLOFIELD LTD (PART NUMBER  FSTX-2225-EU) DOES

1

3

1

2

Отзывы: