Siklu EtherHaul Скачать руководство пользователя страница 153

Страница: 153 / 156

EtherHaul Operation, Administration and Maintenance Manual

Page 153

Presented per port: Eth0 (RF interface of the bridge), Eth1 to Eth4 – 96 intervals of 15
minutes (last 24 hours).

Radio statistics counters – recording 96 intervals of 15 minutes (last 24 hours) recording
the following parameters:

Attribute

Description

Incoming Octets (in-octets)

The total number of octets received on the interface,
including framing characters.

Incoming Unicast Packets (in-ucast-
pkts)

The number of unicast packets received on the
interface.

Discarded Incoming Packets (in-
discards)

The number of packets which were chosen to be
discarded due to RX FIFO full.

Erroneous Incoming Packets (in-
errors)

The number of received erred packets.

Outgoing Octets (out-octets)

The total number of octets transmitted out of the
interface, including framing characters.

Outgoing Unicast Packets (out-ucast-
pkts)

The number of unicast packets transmitted out of the
interface.

Discarded Outgoing Packets (out-
discards)

The number of outbound packets which were chosen to
be discarded due to excessive collision or excessive
deferral.

Erroneous Outgoing Packets (out-
errors)

The number of outbound packets that could not be
transmitted because of errors.

Incoming Multicast Packets (in-
mcast-pkts)

The number of multicast packets received on the
interface.

Incoming Broadcast Packets (in-
bcast-pkts)

The number of broadcast packets received on the
interface.

Outgoing Multicast Packets (out-
mcast-pkts)

The number of multicast packets transmitted out of the
interface.

Outgoing Broadcast Packets (out-
bcast-pkts)

The number of broadcast packets transmitted out of the
interface.

16.4

VLAN Statistics

VLAN statistics counters (since last cleared) are presented per bridge component, per
port and per VLAN ID, recording the

in-pkts, out-pkts

and

drop-pkts

Note that packets may be dropped due to traffic exceeding the radio link’s maximum
bandwidth.

Содержание EtherHaul




























































































































































Результаты поиска

Содержание EtherHaul

Отзывы:

Бренды по названию

Популярные бренды

Siklu EtherHaul, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EtherHaul

Отзывы:

Бренды по названию

Популярные бренды