Siklu EtherHaul Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 156

Siklu EtherHaul Скачать руководство пользователя страница 108

EtherHaul Operation, Administration and Maintenance Manual

Page 108

12.5

ERP Timers

Different timers are used to determine the time of fault reports and switching in order
to assure only necessary switching for permanent failures.

Timer

Description

Hold-off

Timer for ensuring stability of failure before triggering action to
avoid reporting a fault in case of intermittent failure.
0..10000 mSec (in 100mSec steps)

Guard

Timer for protecting device against old R-APS messages.
10..2000 mSec (in 10mSec steps)

Wait-to-Block Timer for delaying switching triggered by administrative

command (FS/MS).
5000..7000 mSec (in 100mSec steps)

Wait-to-

Restore

Timer for delaying revertive operation.
1..12 minutes

12.6

Sample ERP Configuration

The following example illustrates an ERP configuration:

Left_Master>show ring
ring 1 ring-id         : 1
ring 1 type         : ring
ring 1 fdb-id          : 1
ring 1 role         : none
ring 1 cw-port         : eth1
ring 1 acw-port        : eth0
ring 1 raps-md-level   : 7
ring 1 raps-svid       : none
ring 1 raps-cvid       : 100
ring 1 version         : v2
ring 1 revertive    : yes
ring 1 hold-off-timer  : 0
ring 1 guard-timer     : 500
ring 1 wtb-timer       : 5500
ring 1 wtr-timer       : 1
ring 1 cw-status-data  : unblocked
ring 1 acw-status-data : unblocked
ring 1 cw-status-raps  : unblocked

Right_Slave_72>show ring

ring 1 ring-id         : 1
ring 1 type         : ring
ring 1 fdb-id          : 1
ring 1 role         : acw-rpl
ring 1 cw-port         : eth0
ring 1 acw-port        : eth1
ring 1 raps-md-level   : 7
ring 1 raps-svid       : none
ring 1 raps-cvid       : 100
ring 1 version     : v2
ring 1 revertive    : yes
ring 1 hold-off-time   : 0
ring 1 guard-timer     : 500
ring 1 wtb-timer       : 5500
ring 1 wtr-timer       : 1
ring 1 cw-status-data  : unblocked
ring 1 acw-status-data : blocked
ring 1 cw-status-raps  : unblocked

«
...
106
107
108
109
110
...
»

Содержание EtherHaul





























































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды