SIKA TP 38 165 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 43

background image

3 Unpacking and inspecting the delivery

TP 38 … / TP 38 … E

Subject to technical changes

Ba_TP38-E_en 12/2014

SIKA Dr.Siebert & Kühn GmbH & Co.KG

Struthweg 7–9

D-34260 Kaufungen

+49 5605 803-54

[email protected]

3 Unpacking and inspecting the delivery



Unpack your calibrator.

The calibrator is delivered in special protective packaging. Keep this protective packaging for sending the
instrument for recalibration or repairs to the manufacturer.



Inspect the delivery first.

Standard delivery temperature calibrator:

- Calibrator
- Sleeve remover
- Mains connection cable
- Test certificate
- Operating instructions

4 Structure of the temperature calibrator

4.1 Overview of components

The temperature calibrators consists of a control unit with operator panel and a metal block. The two
components are accommodated in a robust metal housing together with fans. In the center of the metal block
there is a bore for holding the probe. Ex works, an integrated measuring instrument can be installed in the
front side of the calibrator (refer to chapter 4.4).

The overview shows a temperature calibrator of the TP 38 165 / TP 38 165 E series, identified by the cooling
fins on the upper side of the calibrator. Instead of the fins, the TP 38 600 / TP 38 600 E calibrator features a
grid for protection against the hot areas of the heating block.

«
...
4
5
6
7
8
...
»

Содержание TP 38 165












































Отзывы:

Нет отзывов

Похожие инструкции для TP 38 165

Veeder-Root 7990 Series

Бренд: Danaher Страницы: 8

Бренд: DriveTest Страницы: 24

Бренд: Mannix Страницы: 5

Micropilot S FMR533

Бренд: E+H Страницы: 12

Бренд: National Instruments Страницы: 169

Бренд: Vectronics Страницы: 28

AquiTron AT-WFM

Бренд: aquilar Страницы: 20

Бренд: Rubicson Страницы: 4

Бренд: Keithley Страницы: 338

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

Бренд: Major tech Страницы: 16

Бренд: AEMC Страницы: 4

Бренд: Banner Страницы: 4

Бренд: Hanna Instruments Страницы: 21

Бренд: Kawai Страницы: 24

AquaInform Sycon 2500

Бренд: WACON Страницы: 52

Бренд: Extech Instruments Страницы: 45

Бренд: Kreg Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды